Insights; Radio Test Function; Deleting The Parameters From The Motor; Copying Parameters And Transmitters - Nice TTPRO Instrucciones Y Advertencias Para La Instalación Y El Uso

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 32

3.8 - Insights

3.8.1 - RADIO TEST FUNCTION

This feature allows for verifying the environmental RF noise level.
Press the button
: on the level LEDs a value appears that represents the
RADIO
01.
TEST
intensity of the ambient signal / RF noise, at 433.92 MHz

3.8.2 - DELETING THE PARAMETERS FROM THE MOTOR

This procedure clears all the parameters in the motor memory and restores the factory
settings.
Hold down the button
until the relative LED starts flashing; Lastly, release
01.
the button.
02.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
Note: this procedure does not delete the transmitters. For this function see 3.4.3 - De-
leting all transmitters.

3.8.3 - COPYING PARAMETERS AND TRANSMITTERS

Using various buttons, you can read the parameters and the transmitters stored in the
motor and then save them in the TTPRO memory. Subsequently, this data can be tran-
sferred to other motors of the same type.
Step 1 - Reading parameters in the memory of the first motor
Warning - Before proceeding, delete the memory of the TTPRO with the procedure
explained in paragraph 3.8.3.1.
Press the button
.
01.
Press one or more buttons (
to copy:
reads the parameters related to the rotation direction and to the limit switches
F1
F2
F3
02.
reads the parameters related to the sensors (wind and sun levels, etc.)
F1
F2
F3
reads the parameters related to the radio transmitters
F1
F2
F3
03.
When TTPRO receives the data, the LED on the key flashes rapidly.
04.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
Step 2 - Writing parameters in another motor
Note: the procedure will only take effect if the motor is of the same type as the one in
which the parameters were read.
Press the button
.
01.
9 – English
RADIO
TEST
RADIO
TEST
/
/
), according to the data you want
F1
F1
F2
F2
F2
F3
F3
F3
F1
RADIO
TEST
Press one or more buttons (
to write:
writes the parameters related to the rotation direction and to the limit switches
F2
F3
F1
02.
writes the parameters related to the sensors (wind and sun levels, etc.)
F1
F2
F3
writes the parameters related to the radio transmitters
F1
F2
F3
03.
When TTPRO transfers the data, the LED on the key flashes rapidly.
04.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.

3.8.3.1 - Deleting of the parameters stored in TTPRO

Press the button
.
01.
RADIO
TEST
Press the following buttons in sequence:
02.
03.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.

3.8.4 - CHECKING THE SOFTWARE VERSION

01.
Press the OK button
➔ The green OK LED flashes: (within 3 sec) press the button
02.
03.
The level LEDs show the version and revision of the software.
04.
After 5 seconds TTPRO turns off automatically.

3.8.5 - UPDATING THE TTPRO FIRMWARE

If you need to update TTPRO (eg. the product software upgrade), contact the
01.
NICE technical support.

3.8.6 - CHANGING THE MOTOR ADDRESS

Press the button
: the actual motor address will start to flash on the level
F1
F2
F3
01.
LEDs.
02.
Use Table 1 to select the new desired address.
Use buttons
and
to select the address you want to assign.
03.
04.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
/
/
), according to the data you want
F1
F1
F1
F2
F2
F2
F3
F3
F3
,
,
.
F1
F1
F2
F2
F3
F3
F1
F2
F3
.
F1
F2
F3

Publicidad

Tabla de contenido
loading

Tabla de contenido