Transmitter Programming; Memorisation Of The Transmitter; Deleting A Single Transmitter; Deleting All Transmitters - Nice TTPRO Instrucciones Y Advertencias Para La Instalación Y El Uso

3.4 - Transmitter programming

BUTTONS DEDICATED TO TRANSMITTERS

3.4.1 - Memorisation of the transmitter

Press and release the button
01.
ly, waiting to receive a transmitter.
(within 5 sec) Press and release any button on the transmitter to be memorised:
02.
➔ the LED on the button flashes quickly.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
03.

3.4.2 - Deleting a single transmitter

Press and release the button
01.
ly, waiting to receive a transmitter.
Press and release the button
02.
transmitter.
(within 5 sec) Press and release any button on the transmitter to be deleted: ➔ the
03.
LED on the button flashes quickly.
04. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.

3.4.3 - Deleting all transmitters

Press and release the button
01.
ly, waiting to receive a transmitter.
Hold down the button and release it when the corresponding LED starts to
RADIO
02.
TEST
flash quickly.
03.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.

3.4.4 - Memorising a single transmitter button (Mode 2)

Press and release the button
01.
ly, waiting to receive a transmitter.
On the transmitter (within 5 sec) press and release the button you want to
02.
store: On TTPRO ➔ LED on the button
Press and release the button
F2
F1
03.
desired command lights up (see the instruction manual of the motor connected
to TTPRO).
Press and release the button
04.
corresponding to the desired level lights up.
05. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
5 – English
DRY
CONT.
: the LED above the button starts blinking slow-
DRY
CONT.
DRY
CONT.
: the LED above the button starts blinking slow-
DRY
CONT.
: the button starts blinking slowly waiting for a
RADIO
TEST
DRY
CONT.
: the LED above the button starts blinking slow-
DRY
CONT.
: the LED above the button starts blinking slow-
DRY
CONT.
flashes quickly.
DRY
CONT.
and wait until the LED corresponding to the
F3
(or the button ) and wait until the LED

3.4.5 - Deleting a transmitter memorised in Mode 2

Press and release the button
01.
waiting to receive a transmitter.
Press and release the button
02.
waiting to receive a transmitter.
On the transmitter (within 5 sec) press and release the button on the transmit-
03.
ter to be deleted: On TTPRO ➔ LED on the button
04. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
If the transmitter is memorised in...
- Mode 2 = the procedure deletes only the button pressed.
- Mode 1 = the procedure deletes the transmitter, regardless of which button you press.

3.5 - Basic programming

3.5.1 - PROGRAMMING THE DIRECTION OF MOVEMENT

On motors with mechanical limit switch you can change the direction of movement as
follows.
If the direction is not programmed, the buttons
01.
movements of the motor; moreover, the LEDs above the buttons
flash at regular and much shorter intervals.
02. Press the button with the desired direction:
03.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
When the operation terminates, the LED on the button corresponding to the cho-
04.
sen direction will be turned on.
Note: at the end of this programming verify if the transmitter Ascent button commands
opening of the roller shutter (or the ascent of the awning), and the Descent button com-
mands the closing of the roller shutter (or the descent of the awning). If the direction is
not the desired one, repeat this procedure to programme the other direction.
: the LED above the button starts blinking slowly,
DRY
CONT.
: the LED above the button starts blinking slowly,
RADIO
TEST
flashes quickly.
and will not control the
and
or .
DRY
DRY
CONT. CONT.
DRY
CONT.
DRY
DRY
CONT.
CONT.