Uninstall (Long Period Of Inactivity) - Adler ECO35 Instalación Uso Y Mantenimiento

Quantity for the first setting should be according to
the installator after evaluating the hardness of the
water and the type of rinse aid used. Recommended
rinse aid standard quantity is 0,16 gr/sec that
correspond to the maximum flow rate of the
dispenser. Recommended
quantity is 0,77 gr/sec that correspond to the
maximum flow rate of the dispenser.
SUGGESTION
To check the effectivness of the rinse aid, look at
freshly washed glasses against the light. Drops of
water remaining on the glass indicate an
insufficient amount while streaks indicate an
excess. (next page)
In case of light coated presence that block
dispenser functions, remove the coat by soaking
the dishes for 30 minutes in a solution water
soap (1:10) before starting machine cycle.
2D3 – DISHWASHERS WITHOUT DETERGENT
DISPENSER
Manually add recommended detergent quantity
from the supplier every 5 cycles. Doses differ
depending on water hardness and soiled
quantity that remain on the dishes.
N.B.
All dishwashers are ready to be installed
external dispenser or specific dispenser kit
through injector and relative tube or through
the hole with relative cap located on the tank
of the machine. If changing to a different
detergent or rinse aid type (even one by the
same manufacturer), you must rinse the
suction and pressure hoses with fresh water
before connecting the new detergent or rinse
aid container. Otherwise, the mixing of
different types of detergent or rinse aid will
cause cristallisation, which may result in a
breakdown of the dosing pump. Failure to
observe this condition will invalidate the
guarantee and product liability.
WARNING!
DETERGENT SELECTION AND DOSAGE ARE
FUNDAMENTAL FOR
RESULTS AND TO
PERFORMANCES FOR
EXTENDED LIFE. FOLLOW ALWAYS THE
INSTRUCTIONS OF THE MANUFACTURER OF
CLEANNING AGENTS. IMPROPER DOSAGES
RESULT IN UNSATISFACTORY
RESULTS AND REPRESENT SOURCES OF
RIVERS AND SEAS POLLUTION. DO NOT USE
detergent standard
WASHING GOOD
MANTAIN MACHINE
LONG TIME AND
WASHING
CORROSIVE OR POLLUTANT PRODUCTS
TO PROTECT AND MAINTAIN
MACHINE, NEVER EXCEED
INDICATED BY
MANUFACTURER. NEVER
DISPENSER DRY OR CHARGED WITH
CORROSIVE OR FOREIGN
WHICH WILL RESULT
WARRANTY.
2E – MAINTENANCE
1- Descale the boiler, the internal surface of
the tank and the appliance water piping
once or twice a year.
2- Descale the rinse and wash jets every
month using vinegar or a descaling
agent.
3- The internal hose of the rinse aid and
detergent peristaltic dispenser should
undergo periodic maintenance (once or
twice a year).
4- Clean solenoid valve filter by extracting it
from the inside of the valve and by
unplugging the water inlet tube.
2F – UNINSTALL (Long period of
inactivity)
Machine can be taken out of operation
only by trained specialists authorized for
the purposes, who will provide for:
1- Shut water line off (water valve) and
electric supply (main breaker).
2- Completely drain the tank.
3- Remove and carefully clean the filters.
4- Completely drain
dispenser hoses, removing them from
the containers.
5- Drain the detergent and rinse aid nozzles
with fresh water first and after with water
and glycerine (50% - 50%) taking care
that nozzles remain clean and lubrified
inside.
6- Drain completely
removing the screw located under the
machine.
7- Spread a thin film of vaseline oil over all
the stainless steel surfaces.
INSTALLATOR REMARKS
INSTALLATION DATE:________________________
INSTALLATION PLACE:_______________________
INSTALLATOR NAME:________________________
MACHINE SERIAL NUMBER:___________________
SIGNATURE:_______________________________
DOSAGES
DETERGENT
LEAVE THE
PRODUCTS
IN LOSS OF
the incorporated
the booster by
11