General Specifications - Klein Tools KN1500P-EX Manual De Instrucciones

ENGLISH

GENERAL SPEcIfIcATIONS

Single Line
Load Rating: 1500 lbs. (675 kg)
Pulling Distance: Max: 138" (3500 mm)
Min: 20" (500 mm)
Double Line
Load Rating: 3000 lbs. (1350 kg)
Pulling Distance: Max: 79" (2000 mm)
Min: 26" (700 mm)
DANGER: The hoist is not an insulating member. Use an appropriate insulating member in series with the hoist to
achieve proper working distances per OSHA Regulation Subpart V, 1926.950 or follow your company's
work practices. Use appropriate clothing and gloves for rated voltage if handle must swing closer to
energized lines than specified by OSHA or your company.
OSHA REGULATION SUBPART V, 1926.950 TABLE V-1
Alternating current - Minimum Distances
Voltage Range Minimum
(Phase to Phase) Working
Kilovolt Distance
2.1 to 15 2 ft. 0 in.
15.1 to 35 2 ft. 4 in.
35.1 to 46 2 ft. 6 in.
46.1 to 72.5 3 ft. 0 in.
72.6 to 121 3 ft. 4 in.
138 to 145 3 ft. 6 in.
• Failure to comply with the following instructions could result in serious injury or death.
• Do not attempt to adjust, repair, or modify any part of the hoist.
• Do not lift more than the rated load.
• Do not operate hoist when it is restricted from forming a straight line with the direction of loading.
• Do not operate hoist with a twisted, kinked, or damaged web strap.
• Do not operate a damaged or malfunctioning hoist.
• Do not lift using hoist.
• Do not use hoist to lift people.
• Do not use hoist to lift loads over people.
• Do not operate hoist with a lever extension.
• Do not remove or obscure warning labels.
Voltage Range Minimum
(Phase to Phase) Working
Kilovolt Distance
161 to 169 3 ft. 8 in.
230 to 242 5 ft. 0 in.
345 to 362 7 ft. 0 in.
500 to 552 11 ft. 0 in.
700 to 765 15 ft. 0 in.
WARNINGS
2
BEfORE OPERATING & HANDLING THE LOAD
Before operating the hoist ensure that:
• The supporting structure or anchoring means have the same or greater load capacity as the hoist.
• The operator has read and understood all information included in this manual, and are familiar with the
operating controls, hoisting practices, and warnings associated with the hoist.
• If any adjustments or repairs to the hoist are needed, report them promptly to a designated person.
• Hoist shall only be used in locations where the operator can be free of the load.
• The operator shall not use a hoist with an out-of-order sign.
• The operator shall not attempt to adjust or repair a hoist, unless qualified to make such adjustments or repairs.
• Hoists shall only be operated by the hand power of one person.
• Hoists shall not be operated with an extension on the handle.
While handling the load, ensure that:
• The hoist web strap is not wrapped around the load.
• The load is attached to the load hook by suitable means.
• The sling or other device is properly seated in the base (bowl) of the hook. The latch shall not be allowed to
support any part of the load.
• The load is not applied to the point of the hook.
• Before applying the load, the operator shall be sure the web strap is not twisted or that multiple parts of the web
strap are not twisted around each other.
• The hoist shall not be operated until the load block, web strap, and hoist body are directly in line with the
direction of loading to avoid sidepull.
• The hoist body or frame is not bearing against any object or the supporting structure.
• The operator shall not apply a load beyond the rated load appearing on the hoist or load block, except during
properly authorized tests.
• Specific attention should be given to balancing of the load and hitching or slinging to prevent slipping of the load.
• The operator shall not release the hoist lever until the ratchet and pawl is engaged and the lever is at rest.
• The operator shall not engage in any activity that will divert the operator's attention while operating the hoist.
• The operator shall not apply a load to the hoist until the operator and all other personnel are clear of the load.
• The operator shall make sure the load clears any obstacles before moving.
• The load shall not be moved more than a few inches until it is well balanced in the sling or lifting device.
• When starting to lift or pull, the operator should move the load a few inches and then check the hoist for proper
load holding action. The operation shall be continued only after the operator has verified the hoist is operating
properly.
• Hoist shall not be used to lift, support, or otherwise transport people.
• The operator should avoid carrying loads over people.
• The operator should not leave a loaded hoist unattended unless specific precautions have been instituted and
are in place.
• Care shall be exercised when removing a sling from under a landed and blocked load.
3