DSC PowerSeries PK5500 Instrucciones De Instalación página 6

Wireless Integration
(RFK55XX Only)
NOTE: Power v4.5 & lower uses 2-digit subsection numbers.
Compatible Wireless Devices
• WLS912L-433 Glass Break Detector * • WS4945 Mini Door/Window Contact*
• WLS914-433 Pet Immune PIR*
WS4965*/WS8965 Tri-Zone Contact
• WS4904(P)*/8904(P) Pet Immune
Wireless Keys
• WS4916*/8916 Smoke Detector
Door/Window Contact
• WS4926 Smoke Detector*
Flood Detector
• WS4938 Panic Button*
• WS4913*/8913 CO Detector**
• WS4939*/8939 Wireless Key
Wireless Repeater*
* Only these models are UL listed.
** CO Detector requires PC1616/1832/1864 v4.5 or higher.
Downloading
The RFK55XX product has an integrated wireless receiver. When
downloading to this keypad, please select the RF5132 v5.4 file. When using
an RFK5564 keypad, please select the RFK5164 v5.4 file. DLS IV must be
used in order to have the capability of downloading to this keypad.
Testing Wireless Devices
1. Temporarily put the wireless devices in the places you want to mount them.
2. At a system keypad, enter [✱][8][Installer Code].
3. Enter programming section [904], then enter the number.
NOTE: If global placement test is enabled (Section
[900], option 8 ON) enter [001] to test all zones.
4. Activate the device being tested until a result is displayed
on the keypad or sounded by the keypad or bell.
Result LED/ICON Keypad LCD Keypad
Light 1 ON Steady
Good Good
Bad Light 3 ON Steady Bad
While in placement test the Ready and Armed LEDs are used to indicate the
reception of a valid signal from a wireless device. The Green (Ready) LED
indicates that a transmission was received from a device that is enrolled on
the system. The Red (Armed) LED indicates that a transmission was
received from a device that is not enrolled on the system. The
corresponding LED will flash once per transmission.
Activate the device until you get 3 good results in a row. Wait
10 seconds between each test on the same device. You may
mount wireless devices where results were good.
Devices indicating a bad result must be moved to another location. You may
only have to move the device a few inches to correct a bad result.
NOTE: Do not mount any device where a
"bad" test result was indi-cated.
:
•
• WS4969
• WS4975/8975
• WS4985/8985
• WS4920
Bell/Buzzer
1 Beep/Squawk
3 Beeps/Squawks
Testing Portable Device Reception
To test portable devices (e.g., WS49X9) press the button(s) at several different points
in the installation to confirm the coverage area. If these devices do not operate from all
points in the installation, you will need to move the RFK55XX.
Receiver Placement Test
The RFK5500/RFK5564 performs best in locations where RF
interference is minimal. To find an optimal mounting location for the
keypad, perform the following placement test:
1. Temporarily connect the Keybus wires to
the keypad (refer to wiring instruc-tions).
2. Hold the keypad in the intended mounting location.
3. Enter keypad programming mode by pressing
[✱][8][Installer Code], then enter section [904].
4. If the yellow Trouble LED is on, interference levels are high and
a new mounting location should be found. If the LED is flashing
or off, interfer-ence is low and the location is good.
Repeater Placement Test
(in event of interference)
(Power v4.6 and higher)
If the "Receiver Placement Test" described above indicated the presence of inter-
ference and you are unable to move the keypad away from the interference source,
perform the following procedure while installing a WS4920 Repeater.
1. Temporarily mount the WS4920 in the desired location.
2. Use the WS4920 to test for signal noise. Refer to the
WS4920 installation manual for instructions.
3. If no noise is detected in the desired mounting location, test for adequate signal
strength through the interference at the RFK5500/RFK5564.
4. At the system keypad, enter [✱][8][Installer Code].
5. Enter programming section [804][900] then set option 1 to
"OFF". This option returns a "good" placement test result if the
WS4920 signal strength in the vicinity of the RFK5500/RFK5564
is within acceptable lev-els through the interference.
6. Exit section [804][900].
7. Enter programming section [904] and perform placement
test as described in "Testing Wireless Devices."
8. If "bad" test results are returned, move the
repeater closer to the RFK5500/RFK5564.
9. Once "good" test results are achieved, set
option 1 in section [804][900] to "ON."
NOTES:
• All devices on the system should be enrolled on
one of the WS4920 repeaters on the system.
•
Perform a Repeater Placement Test only when installing the RFK5500/
5564 in areas of high interference. The preferred solution is to move the
receiver to another location. Please move the receiver as an alternate to
installing a WS4920 repeater.
• Do not install both repeater and receiver in high noise areas.