Attaching The Hose - Black+Decker FSMH1321 Manual De Usuario

ENGLISH
Attachin
g the hand held steam cleaner (Fig. B)
Holding the back of the steam mop body (11) push the
u
hand held steam cleaner (5) firmly into the steam mop
body (11) making sure it sits correctly over the interface
(11a) and clicks securely into place.
Removing the hand held steam cleaner (Fig. B)
Push the release button (10) on the main body (11) and lift
u
the hand held steam cleaner (5) off the interface (11a) and
away from the main body (11).
Attaching a cleaning pad (Fig. C)
Replacement cleaning pads are available from your
BLACK+DECKER dealer :- (cat no. FSMP20-XJ).
Place a cleaning pad (13) on the floor with the velcro 'loop'
u
side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(13).
Note: This unit may be supplied with a standard floor cleaning
head (12) or a steam burst cleaning head (12a). In either case
use these instructions to fit a cleaning pad.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Removing a cleaning pad
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop.
Do not wear slippers or open toed footwear.
Return the handle (8) to the upright position and turn the
u
steam mop 'OFF'.
Wait until the steam mop cools down (approximately 5
u
minutes).
Lift the steam mop away from the cleaning pad freeing it
u
from the velcro fastening.
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (8) supported in
the upright position when stationary and make sure the steam
mop is turned off when not in use.
Filling the water tank (Fig. Q)
Note! Fill the water tank with clean tap water (Do not use any
additives or chemicals).
Note! In areas of hard water, the use of de-ionised water is
recommended.
Open the filler cap (4) by flipping it up.
u
Fill the water tank with water (Do not use any additives or
u
chemicals).
Warning! When filling, detach from main unit and maintain in
a horizontal position.
8
(Original instructions)
Warning! Your water tank has a 0.5 litre capacity. Do not over
fill the tank.
Close the filler cap (4).
u
Note! Ensure the filler cap is firmly secured.
Attaching the carpet glider (12b) (For use on
carpets only)
Place the carpet glider (12b) on the floor.
u
Attach a cleaning pad to the floor cleaning head (12)
u
Lightly press the steam mop down onto the carpet glider
u
(12b) until it clicks into place.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Removing the carpet glider
Caution! Always wear suitable shoes when changing the
carpet glider on your steam mop. Do not wear slippers or
open toed footwear.
Return the handle (8) to the upright position and turn the
u
steam mop 'OFF'.
Wait until the steam mop cools down (approximately 5
u
minutes).
Place the front of your shoe onto the carpet glider removal
u
tab and press down firmly.
Lift the steam mop up and off the carpet glider.
u
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Attaching the hose and accessories to the
hand held steam cleaner (Fig. G - O)
Warning! Inspect the seal between the connection point on
the hand held steam cleaner (5) and the steam hose (16)
before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.

Attaching the hose

Press the steam hose release button (16a) on the steam
u
hose (16).
Connect the steam hose (16) to the hand held steam
u
cleaner (5) and release the steam hose release button
(16a) making sure it clicks into place.
Important! Ensure that the steam hose (16) is securely
connected to the hand held steam cleaner (5). If steam
escapes from the joint, the hose is incorrectly fitted. Switch off,
allow the unit to cool then remove and refit the hose.