Bandini Industrie GiBiDi BA230 Manual Del Usaurio página 26

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 47
26
UK
MENU C: FUNCTION SELECTION
Menu
Function
C1
AUTOMATIC
C2
CLOSING
C3
FAST CLOSING
C4
C5
PRE-FLASHING
C6
C7
SAFETY DEVICE
TEST
C8
C9
LIMIT SWITCH
C10
C11
DECELERATIONS
C12
C13
WATER HAMMER
C14
C15
FINAL CLOSING
STROKE
C16
C17
HYDRAULIC LOCK
RETENTION
C18
C19
C20
AUTOMATIC
C21
PROGRAMMING
C22
HYDRAULIC MOTOR
C23
C24
FIXED FLASHING
LIGHT
C25
* NOTE: If motion is inverted from opening to closing and vice versa, the opening and closing times will be the same in the case of an
electromechanical configuration, but different in the case of a hydraulic configuration in order to take into account the different speed
at which the operator runs in the two phases. In some hydraulic applications where the operators run at the same speed during
opening and closing (e.g. FLOOR 810), it is advisable to enable electromechanical configuration.
Status
Description
E
Enables automatic closing. Also see menu H9.
E
Disables automatic closing.
Enables the fast closing function. Operation: Active only on photocell 1.
Reduces the pause time to 3 seconds following interception and subsequent
E
freeing of the photocells.
Disables the fast closing function.
E
Enables 3-second pre-flashing for motor start.
E
Disables pre-flashing The flashlight and the motors start at the same instant.
E
Enables the safety device test.
Operation: When the Start or Pedestrian command is given, the flashlight starts and
at the same time the power to the safety devices is cut for 0.5 seconds and then
E
restored: if the inputs of the safety devices go back to N.C., the motors start,
otherwise a fault is signalled with 3 long flashes.
Disables the safety device test.
E
Enables limit switch reading. When the limit switches are activated, deceleration
(if activated) starts upon reaching the limit switches and continues for the time
E
H3 and H6. When the limit switches are activated and deceleration is
deactivated, the limit switches stop the motion.
E
Disables limit switch reading.
E
Enables the deceleration function.
E
Disables the deceleration function.
Enables the water hammer function.
Operation: When the Start command is given, before starting the opening phase a
E
3-second closing pulse is given to aid release of the electric lock.
Disables the water hammer function.
E
Enables the final closing stroke function
Operation:
At the end of the run time during closing without deceleration, a 1-second pulse is
E
given at full power, irrespective of the force adjustment When deceleration is active,
the pulse is given at the end of the deceleration period.
Disables the final closing stroke function.
E
Enables the hydraulic lock retention function.
Operation:
E
Only for hydraulic operators. If the gate has not performed any manoeuvres in
the last 4 hours, a 5-second closing pulse is given.
E
Disables the hydraulic lock retention function.
-
Not implemented.
-
Not implemented.
Enables time programming in self-learning
E
Operation: See "Time self-learning procedure".
The operator is hydraulic.*
E
The operator is not hydraulic and it is advisable to program the decelarations.*
E
Enables the flashing light with fixed output.
WARNING: for the blinking function, it is necessary to connect a flashing light board
E
with blinking circuit.
Disables the flashing light with fixed output.
E
BA230

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

As05040

Tabla de contenido