Chicco BebeCare easy-tech Instrucciones De Uso página 9

«Log in» you need to tap on the associated device to connect
it. To maintain the automatic connection between the Chic-
co BebèCare easy-tech device and the Chicco BebèCare, we
suggest that you do not to log out unless absolutely necessary.
• Do not quit the App (do not switch up the App) in order
to guarantee the correct functioning of the system in
any condition.
• In order to verify the correct operation of Chicco BebèCare
easy-tech, it is important to periodically carry out tests to open/
close the accessory, verifying the relative state of the APP
(Chapter 1.1, paragraph (e)).
Failure to comply with the above will result in malfunctioning
of Chicco BebèCare easy-tech and/or the Chicco BebèCare
APP and the consequent disabling of the system and/or failure
to send and/or receive alarm messages.
CAUTION
Check to perform each time Chicco BebèCare easy-tech
is used:
• Check that the smartphone is on and has enough battery
life when using Chicco BebèCare easy-tech.
• Bluetooth® must be active.
• "Airplane" mode must be deactivated.
• GPS must always be active.
Check the Chicco BebèCare APP for sufficient alarm mes-
sages. If this is not the case, proceed with the purchase of
the necessary package.
• If two or more smartphones are used that have the Chicco
BebèCare APP installed, it is necessary to identify which one
is actually connected to the equipment.
• Before each trip, check that the equipment is completely
closed and that the state detected by the Chicco BebèCare
APP is "connected - child seated."
Failure to comply with the above will result in malfunctioning
of Chicco BebèCare easy-tech and/or the Chicco BebèCare
APP and the consequent disabling of the system and/or
failure to send and/or receive alarm messages.
1.1 HOW TO ACTIVATE CHICCO BEBÈCARE EASY-TECH
a) Download the Chicco BebèCare APP
The Chicco BebèCare APP must be downloaded. When accessing
for the first time, the APP will provide all the instructions to follow
to register the account and use Chicco BebèCare easy-tech.
b) Create the family account
A "family account" must be created with a single password. This
account will be the only one that can be used by those who use
that specific equipment. The password is shared with all users who
will interact with the equipment.
IMPORTANT: When creating the family account, an internet con-
nection must be available (mobile data or WiFi network).
IMPORTANT: In the event that the family password is changed,
the new password must be shared with all users who share the
same family account.
c) Enter the emergency numbers
The emergency numbers to which the alarm mes-wise (second
level) containing the data required to geolocate the child must be
entered when accessing for the first time. A minimum of 3 to a
maximum of 5 emergency numbers can be entered. The emer-
gency numbers must be selected from the contacts in your smar-
tphone and can be added, deleted and/or replaced in the future.
IMPORTANT: During this operation, an internet connection must
be available (mobile data or WiFi network).
IMPORTANT: The emergency numbers must be mobile phone
numbers and not landline or national emergency numbers.
IMPORTANT: Always check that the emergency numbers are
correct and are functioning after entering them.
d) Associating the equipment with the family account
To associate your Chicco BebèCare easy-tech equipment with
your family account, carefully follow the instructions in the Chicco
BebèCare App, paying attention to the following.
1) Scan the QR code which is located inside the package
2) Close the equipment (until the Chicco logo is completely visible
through the window in the white casing) (Fig.1) to proceed with
the first association. To ensure Bluetooth® connection, make sure
you are close to your smartphone. The system activates/connects
a few seconds after the device is closed.
Up to a maximum of 4 Chicco BebèCare devices can be associa-
ted with the same family account (child car seats with integrated
sensors and/or anti-abandonment devices). The specific car equi-
pment can be associated permanently with one family account
ONLY.
IMPORTANT: When scanning the QR code, an internet con-
nection must be available (mobile data or WiFi network).
e) Check the correct operation of the equipment
When using the first time, to verify the correct operation of Chicco
BebèCare easy-tech, it is important to do some tests, verifying the
relative state of the APP as follows:
- Close the accessory; state detected by the Chicco BebèCare
APP "connected - child seated"
- Then open the accessory: the possible states detected by the
APP are either "connected" or "disconnected" depending on how
long it takes between opening the accessory and displaying it in
the APP.
f) Enter the information about the baby
After associating the equipment with the family account, enter
the name and date of birth of the child. You can also enter a
photograph.
1.2 HOW CHICCO BEBÈCARE EASY-TECH WORKS
Place the child on the seat and secure him with the restraint
systems provided for the type of seat in use.
Use the clip (A) on the white casing of the equipment to attach
the accessory preferably to the shoulder strap of the seat or to
the diagonal portion of the seat belt (Fig.2). Now completely
close the equipment as indicated in Chapter 1.1, paragraph d),
item 2.
When closed with the Chicco logo fully visible through the
special window on the white outer shell, the user is notified that
the product has been activated by means of a special wake-up
acoustic signal.
This is followed by an intermittent sound that informs the user
that the product is searching for the Bluetooth® signal from the
smartphone. A "beep" notifies the user once the connection has
been made successfully. Make sure that the state detected by
the Chicco BebèCare APP is "connected - child seated." From
this moment on, the equipment is active and the presence of
the child can be monitored through the Chicco BebèCare APP.
WARNING! If the connection does not occur within 20 se-
conds, the user is notified by a short acoustic signal (failed