Product Description And Specifications - Bosch HGS 0 602 211 Serie Manual Original

OBJ_BUCH-2509-002.book Page 18 Tuesday, October 25, 2016 2:36 PM
18 | English
 Connect the machine to a mains supply with proper
earthing connection. Socket outlet and extension cable
must be equipped with an operative protective conductor.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Safety Warnings for the Power Supply of High-
frequency Tools
 The safety warnings and working instructions of the
frequency converter are to be strictly observed! For de-
tailed information, contact the manufacturer of the fre-
quency converter.
 The frequency converter must be secured with a resid-
ual current protection device when working in an envi-
ronment where special protection for persons is neces-
sary. The special protection of persons is required, for
example, when working in damp rooms or with materials
that can produce current-conducting dust. Not using a re-
sidual current protection device can lead to electrical
shock, risk of fire, or serious injuries.
 The residual current protection device should be in-
stalled in the power supply network only by a qualified
electrician. Only in this manner can proper functioning be
ensured.
 The output voltage and frequency of the frequency
converter must correspond with the data on the type
plate of the high-frequency tool.
 Operate the power tool exclusively with a fitting plug.
The CEE plug must be dimensioned for the nominal current
that the power tool requires (see "Technical Data").
 Plug mounting and connection to the power supply is to
be carried out by a qualified electrician trained in han-
dling high-frequency tool systems.
 Use only original cables! Before each use, check the
power tool, cable and plug for possible damage. Cables
and plugs may not be repaired, but must be exchanged in
order to avoid danger.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Technical Data
High-frequency straight grinder
Article number
Rated voltage
Frequency
Rated power input
1 609 92A 36J | (25.10.16)
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Intended Use
The machine is intended for grinding and deburring metal us-
ing corundum grinding accessories.
Use only the blade guards and clamping nuts provided or spe-
cifically released for this power tool.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Grinding accessory
2 Protection guard for grinding
3 On/Off switch
4 Grinder spindle
5 Mounting flange
6 Clamping nut
7 Two-pin spanner for clamping nut
8 Locking screw for protection guard
9 Open-end spanner for mounting flange
10 Cable strain relief (CEE plug)
11 Plug insert (CEE plug)
12 Screw (CEE plug)
13 Screws in plug insert 11 (CEE plug)
14 CEE plug
15 Plastic sleeve (CEE plug)
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Notes on the Power Supply
The power tool is part of a high-frequency system and re-
quires three-phase current with a frequency according to the
type plate.
To reach this frequency, the power tool must be connected
with a frequency converter (see "Connection to the Power
Supply", page 21).
0 602 211 ...
... 507 ... 534
V 72 200
Hz 200 300
W 950 1450
0 602 212 ... 0 602 212 ...
... 404 ... 407
135 72
200 200
950 950
Bosch Power Tools
0 602 213 ...
... 434
200
300
1450