Descargar Imprimir esta página

Switching Between The Paired Cameras; Scan Mode - Automatic Switching Between The Paired Baby Units (Cameras) - BabySense V24UK Guía De Usuario

Publicidad

Idiomas disponibles

Idiomas disponibles

• Place the baby monitor in a place where the air can circulate freely and avoid blocking ventilation and
speaker openings.
• Aim the camera(s) to best optimize the viewing area: Select a location for the camera that provides a
clear view of the area you want to monitor, which is free from dust, and is not in line-of-sight to a
strong light source or direct sunlight. Avoid installing the camera where there are thick walls or
obstructions between the camera and the monitor.
• To use your parent unit and baby unit together, you must be able to establish a radio link between
them, and the range will be affected by environmental conditions:
- Any large metal object, like a refrigerator, a mirror, a filling cabinet, metallic doors or reinforced
concrete between the baby and parent unit may block the radio signal.
- The signal strength may also be reduced by other solid structures, like walls, or by radio or electrical
equipment, such as TV, computers, cordless or mobile phones, fluorescent lights or dimmer switches.
- Use of other 2.4GHz product, such as wireless networks (Wi-Fi routers), Bluetooth systems, or
microwave ovens, may cause interference with this product, so keep the baby monitor away at least
5ft (1.5m) from these types of products, or turn them off if they appear to be causing interference.
Note: If you place the Parent and Baby units too close together you will hear a high pitched noise
called "feedback", this is normal. The units are designed to be located in separate rooms.
5. Operating The Monitor
5.1 Pairing the Baby Unit with Parent Unit
Baby Unit is paired to the Parent Unit when supplied. There is no need to pair the units again unless the
Baby Unit loses its link with the Parent Unit. To renew the pairing of your units or pair a new/additional
Baby Unit, follow the procedure below:
Note: Before you begin pairing, be sure to have the Baby and Parent Units side by side and turned on.
• Press the MENU/Exit key (12) and the menu screen will be displayed on the Parent Unit.
• Press the LEFT key (10) or RIGHT key (8) until the camera icon is highlighted in red then press UP
key (5) or DOWN key (9) to select the desired camera to pair.
• Press OK key (6) to start the pairing.
• The chosen camera will start blinking. Press and hold the PAIR button (23) in the back of the Baby Unit
until the connection is established.
• Once paired, an image from the paired camera will display on the screen.
• If unsuccessful, please repeat above steps.
• Press the MENU/Exit key to Exit (12).
Note: If there is more than one camera to be paired, repeat the above steps for each camera individually.

5.2 Switching between the paired cameras

NOTE: This func�on is only available when two or more cameras are paired.
• To switch between the paired cameras, press the OK key (6) on the parent unit.
• When pressing the OK key (6) , it will switch the view to the next paired camera.
• On the top of the LCD display you will see the number of the camera it is connected to.
• Do not try switching between the cameras through the menu as it is intended for PAIRING purposes only.

5.3 Scan Mode - Automatic switching between the paired Baby Units (Cameras)

You can set the SCAN (loop) mode and each paired Baby Unit will be displayed on the screen for 10
seconds and then the screen will automatically change to the next paired Baby Unit.
• Press OK key (6) until the Scan/Loop icon is displayed on the top of the LCD screen.
• In this mode each paired camera will be displayed on the screen for 10 seconds and
then the screen will automatically change to the next paired camera.
• The loop mode is activated between the last paired camera and the first one.
• To deactivate this mode, press the OK key (6) until you will see the desired camera
number on the top of the LCD screen.
EN
4

Publicidad

loading

Productos relacionados para BabySense V24UK