Caractéristiques Techniques - SUHNER ROTOstar Documentación Técnica

6 Idler wheel
7 Contact wheel
Suitable Tools: See catalogue
• Grinding belts
• Compressed non-woven belt with textile insert
Tool change (belt)
• Press idler wheel end 11 against a solid base. This causes the
belt tension to drop.
• Do not press down on idler wheel 6. Belt-tightening mechanism
otherwise becomes blocked for safety reasons.
Remove grinding belt from contact wheel and fit new belt.
Disassembly/assembly of the contact wheels
• Loosen hexagon nuts 4 with box spanner 2.
• Remove contact wheels 6, 7.
• Clean drive spindle 9 and mounting pivot 10.
• See Fig. G for the order of assembling the components.
• Firmly tighten hexagon nuts 4 with box spanner 2 (hold large
contact wheel 7 firmly in place while doing so.)
• Ensure that hexagon nuts 4 are securely tightened.
Before start-up
Also take note of the following points before start-up:
• Starting without safety guard 1 is not permissible.
• Defective, worn or vibrating contact wheels 6, 7 must be re-
placed under all circumstances.
• Belt track : Position idler wheel 6 parallel to contact wheel 7 with
tracking bolt 12.
• Trial run: Adjust belt at lowest speed. Grinding belt 3 must run
symetricly to the contact wheel.
• Replace grinding belts with poor running performance.
• Never direct the open belt side against persons.
• Never reach into the open belt side.
• Do not push idler wheel end against firm objekt, while operating
(uncontrolled belt running.)
4. FSM Right angle grinder
4
Gear transmission ratio approx.
Gear transmission ratio approx.
Tool connection
Permissible operating speed up to
Max. tool up to
Spindle (see spare parts list)
Veuillez lire les conseils de sécurité, annexe 30003471 !
1. Rotostar: caractéristiques techniques
2. Arbre flexible
3. Mise en service
3.1 Réglage du régime de travail
3.2 Branchement de l'arbre flexible
3.3 Branchement de l'accouplement de sécurité SAK
3.4 Branchement des embouts de travail
3.5 Mise en service avec SAK
4. Accessoires: FH 10, WI10, BSG10, FSM
1. Rotostar
voir figure A
Composants
A1 Contacteur de marche/ arrêt
A2 Goupille d'arrêt
A3 Repère de régime de rotation
Caractéristiques techniques
Moteur universel monophasé à courant alternatif
Puissance absorbée:
6
13 Centre of rotation of the
angular head
see Fig. H
Type 1:1 i = 2:1
Type 2:1 i = 2:1
G28 = ø 28 mm
12,000 RPM
180 mm
M14 or 5/8"-11
FR
A4 Régimes de rotation
A5 Excentrique
A6 Accouplement moteur
1.700 W
Weight
For shaft type:
Machine elements
1 Allen wrench
2. Screw
3. Handle mount
4. Side handle
5. Wheel guard flange
6. Wrench 17 mm
7. Spindle
8. Allen wrench
9. Wheel guard
Change of side handle from left to right
• Release and then firmly tighten threaded element 2 of handle
mount 3 with allen wrench 1.
Wheel guard
In order to operate reinforced grinding and cutting wheels, the
wheel guard must be installed.
Wheel guard assembly and adjustment:
Mount wheel guard 9 to the wheel guard flange 5, set guard at
required position and tighten screw with allen wrench 8.
Suitable Tools:
11,12 Reinforced Grinding and Cutting wheels, Flap discs ,
Diamond discs 4 1/2"
16 Backing pads with fiber discs 17, flange nut 15, Velcro pads
and discs
18 Wire cup brushes etc.
Change of tools / abrasives
• Hold spindle 7 firmly in place with wrench 6.
• Release or tighten flange nut 13 (15) with pin wrench 14.
Accessories
All accessories can be found in the SUHNER Abrasive Power
Tool catalog.
Subject to change.
Puissance restituée:
Isolation en classe
Tension (voir liste des pièces de rechange)
Démarrage progressif et sans à-coups
Charbons à déclenchement automatique
Poids sans arbre flexible:
Régimes de rotation à vide:
Niveau sonore EN 60745
Niveau sonore sous charge
K =
Raccord d'arbre flexible
Pour arbres flexibles de types:
(voir catalogue)
Mesures de vibrations ISO / DIS 8662/4
Type Disque
d'embout: d'essai:
FH10 ø 80 x 10
WI10 ø 50 x 6
BSG 10 ø100 x 25
FSM 10 ø180 x 6
K =
1.2 kg
NA 12 DIN 10 / G28
10. Clamping flange
11. Grinding wheel
12. Cut-off wheel
13. Flange nut
14. Pin wrench
15. Flange nut
16. Backing pads
17. Fibre disc
18. Directly attachable tools
1.250 W
II
diverses V
uniquement en 230 V
2
10 kg
12.000 tr/mn
6.000 tr/mn
3.000 tr/mn
89 dB(A)
102 dB(A)
3 dB(A)
DIN 10 = M10 voir A6
NA 12 DIN 10 / G28 voir B2 B8
NA 10 DIN 10 / G28
Valeur de Position de
mesure: l'excentrique
2
< 2,5 m/s 12.000 tr/mn
2
< 2,5 m/s 12.000 tr/mn
2
< 2,5 m/s 6.000 tr/mn
2
< 2,5 m/s 6.000 tr/mn
2
1,5 m/s