Publicidad
Idiomas disponibles
Idiomas disponibles
NOTE: If any tension is found between the front keypad assembly and the
wiring, open the keypad, reroute the wire and close again. Repeat these
steps until the keypad is closed properly.
Wiring
1. Before wiring the unit, ensure that all
power (AC transformer and battery) is dis-
connected from the control panel.
2. Connect the four Corbus wires from the
control panel (red, black, yellow and green)
to the keypad terminals. Refer to the dia-
gram:
If programmed as an input, a device - such
as a door contact - may be connected to the
'P/Z' terminal of the keypad. This elim-
inates the need to run wires back to the con-
trol panel for the device. To connect the zone, run one wire from the
device to the 'P/Z' terminal and the other wire from the device to the B
(black) terminal. For powered devices, run the red wire to the R (positive)
terminal and the black wire to the B (negative) terminal. When using end
of line supervision, connect the zone according to one of the configurations
described in the PowerSeries Neo Reference manual.
NOTE: For UL/ULC installations, the zone input is a supervised type
(SEOL/DEOL). The supervision resistor is 5600Ω. If no EOL supervision
is used, there is a three foot maximum distance required for the connected
device. Use only in conjunction with UL/ULC listed devices.
NOTE: This initiating device connected to this input contact is not to be
used for medical or fire applications.
3. If the 'P/Z' terminal is programmed as an output, a small relay (such as
DSC model RM-1 or RM-2) or buzzer or other DC operated device may be
connected between the positive supply voltage and the 'P/Z' terminal
(max.load is 50mA).
NOTE: For UL/ULC-listed installations, use UL/ULC listed devices.
Apply Power
Once all wiring is complete, and the equipment is secured to the building
structure with at least two screws, apply power to the control panel:
1. Connect the battery leads to the battery.
2. Connect the AC transformer.
For more information on control panel power specifications, see the Power-
Series Neo Reference manual.
Program the Keypad
1. Press [*][8][Installer Code].
2. Use the [<][>] keys to navigate
through the menus or jump directly to a
specific section by entering the section
number.
Programming consists of toggling on
and off options in each section or by pop-
ulating data fields. Toggle options are
enabled or disabled by pressing the cor-
responding number on the keypad. For
example, to enable toggle options 1 and
4, press the [1] and [4] keys. All
enabled options are displayed (see the
following diagram).
1. To input data, use the [<][>] keys to select a character then press the
keypad button for the number/letter.
2. Using the [<][>] keys, scroll to the next character and repeat the pro-
cedure. For information on entering HEX data, refer to the PowerSeries
Neo Reference manual.
Language Programming
Enter [000][000]. Enter the two-digit number corresponding to the language
desired:
Table 2: Languages
01 = English
10 = German
(default)
11 = Swedish
02 = Spanish
12 = Norwegian
03 = Portuguese
13 = Danish
04 = French
14 = Hebrew
05 = Italian
15 = Greek
06 = Dutch
16 = Turkish
07 = Polish
17 = Future Use
08 = Czech
18 = Croatian
09 = Finnish
19 = Hungarian
Enroll the Keypad
Keypads can be enrolled automatically or manually. In either case, the
serial number of the device is used as an identifier.
NOTE: If there is no keypad enrolled on the system, once you power up,
the keypad will display the message: Press any key to enroll. Other
keypads can then be enrolled from the first keypad. Use one of the fol-
lowing enrollment options:
[902][000] Auto Enroll
When this mode is selected, the total number of keypads currently enrolled
1
4
is displayed on the keypad.
1. Enter [902][000] to begin the auto-enrollment of new keypads. As each
device is enrolled, the keypad displays the model type, serial number and
slot assignment. Keypads are assigned to the next available slot.
Toggle
(X)
<>
[902][001] Manual Enroll
"Toggle name"
Y/N
To manually enroll individual keypads:
1. Enter [902][001] or use the [<][>] keys and press [*].
2. When prompted, enter the serial number of the keypad found on the back
of the device.
3. An error tone is sounded if an invalid serial number is received. Once
enrolled, the device model, serial number and slot assignment are dis-
played. Keypads are enrolled into the next available slot for the device.
The slot assignment can be changed using the [<][>] keys.
4. To cancel the enrollment of a module, press [#].
NOTE: Once the maximum number of devices have been enrolled, an error
tone sounds and a warning message is displayed.
[902][002] – Module Slot Assignment (LED, LCD,
ICON)
This section is used to change the slot number in which a module is
enrolled. To change the slot number:
1. Enter [902][002] or use the [<][>] keys and press [*].
20 = Romanian
2. Enter the serial number of the module.
21 = Russian
3. When prompted, enter the new two-digit slot number. The previous slot
22 = Bulgarian
assignment is replaced with the new one. An error tone sounds if an
23 = Latvian
invalid slot number is entered.
24 = Lithuanian
[902][003] – Module Slot Assignment (LCD Only)
25 = Ukrainian
Similarly to [002], this section is also used to change the slot number of a
26 = Slovak
module. With this option, however, the serial number is not required. To
27 = Serbian
change the slot number:
28 = Estonian
1. Enter [902][003] or the use the [<][>] keys and press [*].
29 = Slovenian
2. Use the [<][>] keys to locate the module then press [*] to select.
3. Enter the new two-digit slot number. The previous slot assignment is
replaced with the new one. An error tone sounds if an invalid slot number
is entered.
[902][101] Unenroll Keypads
1. Enter [902][101] or use the [<][>] keys and press [*].
2. Use the [<][>] keys to scroll to the specific keypad to delete.
Publicidad
