Cooper Lighting HALO RL560 Serie Instrucciones página 2

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

2. Connect other end of ground wire to housing.
Connection to housing may vary depending
on model. Three connection methods are
described below.
Use existing screw inside housing (Fig. 2).
Use supplied #8 nut on existing stud (Fig. 3).
Use supplied #8 screw (B) in existing hole (Fig. 4).
DETERMINING WHICH INSTALLATION
METHOD TO USE
For 6" housings with torsion spring receiving
brackets:
NOTE: Module ships with torsion spring pre-installed
in the 6" bracket position.
No further assembly required.
For 6" housings without torsion spring receiving
brackets (see page 1 in the HOUSINGS section of
these instructions for a listing of the most common
housings):
1. Remove torsion spring brackets completely (keep
screws) (see Fig. 5).
2. Locate friction clip with "6" cut out (see Fig. 6).
3. Attach friction clip to base with "6" (use screw
from Step 1) (see Fig. 6).
4. Repeat 1-3 for second clip.
Fig. 2
(View from inside the housing)
Ceiling thickness
adjustment slot
Ground
(one of three slots
wire
inside housing)
Fig. 3
(View from inside the housing)
#8 Nut
Threaded stud
Ground
in side wall of
wire
housing
Fig. 4
(View from inside the housing)
B
Ground
Existing hole
wire
Fig. 5
6" Housings using Torsion
Spring Bracket
Torsion Spring Bracket in the
outward position
Fig. 6
6" Housings using Friction Clip
Blades
Friction clip installation for 6"
housings in the outward position
For 5" housings with torsion spring receiving
brackets:
NOTE: Module ships with torsion spring pre-installed
in the 6" bracket position.
1. Loosen torsion spring bracket screw (Fig. 5).
2. Slide bracket to inward position such that the
bracket fits over the guide on the heat sink and
screw is positioned next to "5" (Fig. 7).
3. Tighten screw.
4. Repeat steps 1-3 for 2nd torsion spring bracket.
For 5" housings without torsion spring receiving
brackets (see page 1 for a list of pre-tested
housings):
1. Remove torsion spring brackets completely (keep
screw) (see Fig. 5).
2. Locate friction clip with "5" cut out ( see Fig. 8).
3. Attach friction clip to base with "5" (use screw
from Step 1) (see Fig. 8).
4. Repeat 1-3 for second clip.
RETROFIT INSTALLATION INTO E26 EDISON
SCREW BASE RECESSED HOUSINGS
NOTE: Confirm housing is compatible with RL560 series
modules. A listing of the most common housings is
provided in the HOUSINGS section of these instructions.
1. Remove mounting bracket and plate from inside
existing recessed housing (if installed).
2. Release socket from plate (if installed).
3. Screw Edison base adapter into existing Edison
base socket in housing (Fig. 9a).
4. Insert orange plug from LED adapter into orange
socket in the module (Fig. 9b).
Important: Orange plug must be fully inserted prior to
installing connection cap in Step 9c.
5. Slide connector cap down over LED connector
(Fig. 9c).
6. Twist cap clockwise to lock.
2
Fig. 7
5" Housings using Torsion
Spring Bracket
Torsion Spring Bracket positions
for installation into 5" housings
Fig. 8
5" Housings using Friction Clip
Blades
Friction Clip installation for 5"
housings
Fig. 9a
E26 Edison
screw base
Fig. 9b
Fig. 9c
LED Connector Cap

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Halo rl560whHalo rl560wh-rHalo rl560wh-cHalo rl560snHalo rl560sn-rHalo rl560sn-c

Tabla de contenido