Festool TS 75 EQ Manual De Instrucciones Original página 5

correct power tool will do the job better and
safer at the rate for which it was designed.
b. Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from the power
c.
source and/or remove the battery pack, if
detachable, from the power tool before
making any adjustments, changing acces­
sories, or storing power tools. Such pre­
ventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfami­
liar with the power tool or these instruc­
tions to operate the power tool. Power
tools are dangerous in the hands of un­
trained users.
Maintain power tools and accessories.
e.
Check for misalignment or binding of mov­
ing parts, breakage of parts and any other
condition that may affect the power tool's
operation. If damaged, have the power
tool repaired before use. Many accidents
are caused by poorly maintained power
tools.
f. Keep cutting tools sharp and clean. Prop­
erly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
Use the power tool, accessories and tool
g.
bits etc. in accordance with these instruc­
tions, taking into account the working con­
ditions and the work to be performed. Use
of the power tool for operations different
from those intended could result in a haz­
ardous situation.
h. Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slip­
pery handles and grasping surfaces do not
allow for safe handling and control of the
tool in unexpected situations.
5 SERVICE
a. Have your power tool repaired by qualified
specialists only and always use original
spare parts. This ensures that the safety of
the power tool is maintained.
Only use original parts for repairs and
b.
maintenance. The use of incompatible ac­
cessories or spare parts can result in elec­
tric shocks or other injuries.
3.2 Safety instructions for specific circular
saws
Cutting procedures
DANGER: Keep hands away from cut­
–
ting area and the blade. Keep your second
hand on auxiliary handle, or motor hous­
ing. If both hands are holding the saw, they
cannot be cut by the blade.
Do not reach underneath the workpiece.
–
The guard cannot protect you from the
blade below the workpiece.
– Adjust the cutting depth to the thickness of
the workpiece. Less than a full tooth of the
blade teeth should be visible below the
workpiece.
– Never hold the workpiece in your hands or
across your leg while cutting. Secure the
workpiece to a stable platform. It is impor­
tant to support the work properly to mini­
mise body exposure, blade binding, or loss
of control.
– Hold the power tool by the insulated han­
dle surfaces if you intend to perform work
that entails a risk of cutting into hidden
power cables or the tool's own power ca­
ble. Contact with live cables transfers an
electric current to metal components on
the electric power tool and causes electric
shocks.
– When ripping, always use a rip fence or
straight edge guide. This improves the ac­
curacy of cut and reduces the chance of
blade binding.
Always use blades with correct size and
–
shape (diamond versus round) of arbour
holes. Blades that do not match the mount­
ing hardware of the saw will run off-centre,
causing loss of control.
Never use damaged or incorrect blade
–
washers or bolt. The blade washers and
bolt were specially designed for your saw,
for optimum performance and safety of op­
eration.
Kickback causes and related warnings
– kickback is a sudden reaction to a pinched,
jammed or misaligned saw blade, causing
an uncontrolled saw to lift up and out of the
workpiece toward the operator;
– when the blade is pinched or jammed tight­
ly by the kerf closing down, the blade stalls
and the motor reaction drives the unit rap­
idly back toward the operator;
English
5