Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
®
Handylectric
Service
1.
Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.
SPECIFIC SAFETY RULES
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
Electric shock resulting in death can occur if you
plug this machine into an improperly wired outlet. If
the ground wire is electrified, you can be electrocuted
by just touching the machine, even when the power
switch is off. A ground fault circuit interrupter will not
protect you in this situation. Use a UL listed tester to
determine if the outlet is safe.
Do not overstress cables. Overstressing cables may
cause twisting, kinking, or breaking of the cable and may
result in serious injury.
1.
Only wear leather gloves. Never use any other type of glove,
such as cloth, rubber, or coated gloves. Never grasp a rotating
cable with a rag. These items could become wrapped around the
cable and cause serious injury.
2.
Do not overstress cables. Overstressing cables because of an
obstruction may cause twisting, kinking, or breaking of the cable
and may result in serious injury.
3.
Place the machine at a distance not greater than six inches
(15cm) from drain opening. Greater distances can result in
cable twisting or kinking.
4.
Machine is designed for ONE-PERSON operation. Operator
must control trigger switch and cable.
5.
Never take hold of a rotating cable. Pull the cable out, or
push it back into the container by hand only when the motor
is stopped. When the motor is turning, always have one
hand controlling the trigger switch and the other hand
around the grip shield. Operator's hand may be caught in the
moving parts resulting in serious injury.
6.
Be careful when cleaning drains where cleaning chemicals
have been used. Avoid direct contact with corrosive drain clean-
ers. Drain cleaning chemicals can cause serious burns, as well
as damage the cable.
7.
Do not operate machine if operator or machine is standing
in water. Will increase risk of electrical shock.
8.
Wear safety glasses and rubber soled, non-slip shoes. Use
of this safety equipment may prevent serious injury.
9.
Before starting each job, check that the cable in the drum is
not broken or kinked, by pulling the cable out and checking
for wear or breakage. Always replace worn out (kinked or bro-
ken) cables with genuine GENERAL replacement cables.
10. Only use this tool in the application for which it was de-
signed. Follow the instructions on the proper use of the ma-
chine. Other uses or modifying the drain cleaner for other appli-
cations may increase risk of injury.
FEATURES
Forward/Off/
Reverse Switch
Variable Speed
Container Back
Trigger Switch
NOTE: Do not operate machine if warning labels on the grip shield
and power cord are missing or illegible.
VARIABLE SPEED SWITCH
A variable speed control is built into the trigger mechanism. You can
control and increase the machine's speed by applying more trigger
pressure until you get the speed that you want.
You can also control the machine's direction of rotation by switching
the forward and reverse lever, which is located just above the trigger
switch. Move the lever toward the Forward arrow for forward rotation
and toward the Back arrow for reverse rotation. Switch to OFF posi-
tion when the tool is not in use.
Cable Application Chart (Table 1)
Cable Size
Pipe Size
1/4"
1-1/4" to 2"
5/16"
1-1/2" to 2"
3/8"
2" to 3"
The 1/4" and 5/16" diameter cables with EL Basin plug heads
can be spun through most strainer crossbars and work well in
lines blocked by soft stoppages such as hair, soap, fats, etc.
4
Chuck (Quick Grip™ Chuck shown)
Basin Plug Head
Cable
Grip Shield
Container Front
Typical Applications
Small lines, tubs, and shower drains.
Sinks, basins, and small drains.
Stacks, toilets, small drains (No Roots).
Publicidad
Tabla de contenido
