Seav BeSAFE RX NEW Manual De Instrucciones página 14

s i m sd B up (d - BK)
aving the nFo on a iCro aCK
With the receiver you can save/archive the informations previously programmed in the
Receiver on a MicroSD card inserted in the INT 2292 interface. Proceed as follows to
save the settings: use the UP or DOWN button to go to the D - BK storage position and
press SEL and SET. Digits 2, 3 and 4 will start flashing, at the same time use the UP or
DOWN button to select one of the following codes OFF or ON and press SET to confirm
the display will show a series of information and, if the operation was successful the
display will show STOR stored or will show FAIL = operation failed.
NOTE: during the receiver Backup procedure is out of service.
NOTE: as soon as you finish entering the date and time, the unit automatically performs
a backup of the events.
NOTE: saving information, is performed automatically after 10 seconds of inactivity
whenever you adhere to a ways-cunt operating a new device or stored on the receiver.
NOTE: the events are automatically saved on the MicroSD each day at 00:00.
RESTORE
With the INT 2292 interface you can download all information previously archived by a
BeSafe RX New Receiver onto another receiver of the same model if required.
The Restore procedure is as follows: press and hold the PUL button on the INT 2292 inter-
face, the display will show READ = successfully read, if the operation will be successful
the display will show STOR = stored or will show FAIL = operation failed.
NOTE: during the receiver Restore procedure is out of service.
SIGNALS
The INT 2292 interface has a signal LED to show the operating status:
- On = Normal operation.
- Flashing = Read/write data flow.
- Off = Faults - Errors - No MicroSD card.
Feature oF miCro sd Card on the pC
Inserted the Micro SD card on the port of a Windows PC, you can change the settings
via the Web App, the time slots, the devices and view Backup events.
Once you have finished editing and executed a rescue remove the MicroSD card from
your PC, you can connect it to the INT2292 and perform a Restore to return all changes
will be on the receiving BeSafe RX New.
FunCtionality oF the miCrosd Card on the int2292
Inserted the MicroSD card on INT2292 interface connected to the PC via Micro USB cable
you can change by means of x Windows Web App, the settings, the time slots, the devices
and view real-time events in addition to Backup events.
When executed a bailout from Web App it will automatically run the Restore also on the
receiving BeSafe RX New.
Also you can take advantage of single Advanced and customized settings for each Device
over standard configurations on the control panel.
NOTE: Using the Web App x Windows is automatically disable the possibility of mofidify
of the riceiver operation BeSafe RX New.
Features oF the WeB app BesaFe neW x WindoWs
The application works only with operating systems WINDOWS 7, WINDOWS 8 and
8.1, WINDOWS 10.
The application is not compatible with USB 3.0 ports.
SETTING TIME ZONE
In the Web App you can configure up to 30 different time slots for each device can be
associated with two time slots choice.
NOTE: The devices that do not have time slots are linked to the global time slot.
NOTE: Leases from 0950 to 0999 are not regulated by time zones.
Key Features graphiCs Key out1 - out2
In the Web App, there are 2 graphics buttons (OUT1 - OUT2) that are used to unlock
manualmentente relays the BeSafe RX New. The buttons only work with the New Be-
Safe RX connected to the PC.
N.B.: The OUT2 button will appear only if you set the function Anti Pass Back 2.
AUTOMATIC SETUP DATE & TIME
In the Web App is a graphical button (UPDATE) that insert or update date and time of the
receiver, in synchronization with the time and date of the PC.
14
Rev.3.0 dated 3/03/2017