Technical Features; Safety; Transportation And Handling; Installation - Calpeda NCE H Serie Instrucciones De Uso

In mixtures with glycol, the information relative to
i
the operating conditions must be corrected.
Use only glycol with anticorrosion protection,
GB
comply with the manufacturer's instructions.
2.2 Improper use
The device is designed and built only for the purpose
described in paragraph 2.1.
Improper use of the device is forbidden, as is use
under conditions other than those indicated in
these instructions.
Improper use of the product reduces the safety and the
efficiency of the device, Calpeda shall not be responsible
for failure or accident due to improper use.
2.3 Marking
The following picture is a copy of the name-plate that is
on the external case of the pump.
1
2
NCE xxxxxxxx
3
230 V - 50Hz
4
P (W)
5 TFxx - IP44
I (A)
Max. xx MPa
6
7 Class xx
EEI ≤0,xx - Part 2
8

3 TECHNICAL FEATURES

3.1 Technical data
Dimensions and weight (paragraph 13.1).
Protection IP 44
Supply voltage / Frequency 230V -10%;+6% 1~50/60 Hz
Insulation class F
Sound pressure <40 dB (A).
The system's maximum permissible pressure is 1 MPa
(10 bar).
3.2 Operating conditions
Installation in well ventilated location protected from the
weather, maximum ambient temperature is related with
pumped fluid.
Ambient temp.
[°C]
up to 25°C
30
35
40

4 SAFETY

4.1 General provisions
Before using the product it is necessary to know
all the safety indications.
Carefully read all operating instructions and the
indications defined for the different steps: from
transportation to disposal.
The specialized technicians must carefully comply
with all applicable standards and laws, including local
regulations of the country where the pump is sold.
The device has been built in conformity with the
current safety laws. The improper use could
damage people, animals and objects.
The manufacturer declines any liability in the
event of damage due to improper use or use
under conditions other than those indicated on the
Page 8 / 56
1 Type
2 Supply voltage
9
3 Fréquence
Made in EU
4 Liquid temperature
07051xxxxx 10
5 Protection degree
min max
6 Max Pressure
11
xx xx
7 Insul. class
xx xx
12
8 Efficiency Class
9 Certifications
9
10 Serial number
11 Power min-max
12 Current min-max
Fluid temp. [°C] Ambient relative
Min. Max. humidity
2 110
2 100
< 95%
2 90
2 80
name-plate and in these instructions.
Follow the routine maintenance schedules and
i
the promptly replace damaged parts, this will
allows the device to work in the best conditions.
Use only original spare parts provided from
Calpeda S.p.A or from an authorized distributor.
Don't remove or change the labels placed on the
device.
Do not start the device in case of defects or damaged
parts.
Maintenance operations, requiring full or partial
disassembly of the device, must be done only
after disconnection from the supply.
4.2 Safety devices
The device has an external case that prevents any con-
tact with internal parts.
4.3 Residual risks
The appliance, designed for use, when used in-line with
the design and safety rules, doesn't have residual risks.
4.4 Information and Safety signals
For this kind of product there will not be any signals on
the product.
4.5 Individual protection devices
During installation, starting and maintenance it is
suggested to the authorized operators to consider the
use of individual protection devices suitable for described
activities.
Signal individual protection device
HAND PROTECTION
(gloves for protection against chemical, thermal
and mechanical risks).

5. TRANSPORTATION AND HANDLING

The product is packed to maintain the content intact.
During transportation avoid to stack excessive weights.
Ensure that during the transportation the packed cannot
move.
The transport vehicles must comply, for the weight and
dimensions, with the chosen product (see paragraph
13.1 dimensions and weights).
5.1 Handling
Handle with care, the packages must not receive
impacts.
Avoid to impact onto the package materials that could
damage the pump.
If the weight exceeds 25 Kg the package must be hand-
led by two person at the same time (see paragraph 13.1
dimensions and weights).

6 INSTALLATION

OFF
6.1 Dimensions
For the dimensions of the device refer to the annex
"Dimensions" (paragraph 13.1 Annexes).
6.2 Ambient requirements and installation site
dimensions
The customer has to prepare the installation site in order
to guarantee the right installation and in order to fulfill the
device requirements (electrical supply, etc...).
The place where the device will be installed must fulfill the
requirements in the paragraph 3.2.
NCE(D) H, NCE(D) HQ Rev. 4 - Operating Instructions