Numark iCDMIX 3 Guia De Inicio Rapido página 5

16. KEYLOCK – Engages the Keylock feature, which locks the musical key of the track to the original key (as if it were
playing with 0% pitch adjustment). You can then adjust the tempo of the track without affecting its key or pitch.
17. TAP – Tap this button in time with the beats of the music on that deck. This will enter a new BPM ("beats per minute")
reading for that track, which will be shown on the LCD. You can allow the automatic beat-counter to read the track's
BPMs by holding it down until "AUTOBPM" is shown on the LCD.
18. RELAY – Press this button to activate or deactivate Relay Play. When activated, relay play will cause the opposite deck
to start playing whenever the currently playing deck stops. Playback will alternate between the two decks until one of
the decks reaches the end of its disc or until Relay Play is deactivated.
19. TIME – Switches the time display between "ELAPSED" playing time, "REMAINING" time on the track, and "TOTAL"
remaining time on the entire CD.
20. SNGL – Press this button to toggle between Single Play (the deck will stop at the end of each track) or Continuous Play
(the entire disc will be played without interruption).
21. ID-3 TAG – Press this button to display additional MP3 information. Pressing it more than once will toggle through all
the available information, including the track title, artist name, name of the current folder, and file name.
22. LCD – Indicates all the functions, as they are occurring, with the CD.
23. INPUT SELECTOR – Selects the input source to be routed to the corresponding channel. Input jacks are located on the
rear panel.
24. CHANNEL GAIN – Adjusts the channel's pre-fader and pre-EQ gain level.
25. CHANNEL TREBLE – Adjusts the high (treble) frequencies of the corresponding channel.
26. CHANNEL MID – Adjusts the mid-range frequencies of the corresponding channel.
27. CHANNEL BASS – Adjusts the low (bass) frequencies of the corresponding channel.
28. CHANNEL FADER – Adjusts the audio level on the corresponding channel.
29. CHANNEL CUE – Sends pre-fader audio to the Cue Channel for headphone monitoring.
30. CUE MIX – Turn to mix between Cue and Program in the Headphone channel. When all the way to the left, only
channels routed to CUE will be heard. When all the way right, only the Program mix will be heard.
31. CUE GAIN – Adjusts the audio level of the Cue channel.
32. HEADPHONES – Connect your 1/4" or 1/8" headphones to this output for cueing and mix monitoring.
33. MIC ON / OFF – Mutes and unmutes the microphone signal. When muted,
the microphone signal will not be routed to the Master mix.
34. CROSSFADER – Blends audio playing between Channels 1 and 2.
Sliding this to the left plays Channel 1 and sliding to the right plays
Channel 2.
35. FADER START – When fader start is "ON," moving the CROSSFADER to a side will cause that deck to start playing
automatically (if it is paused). When fader start is "OFF," you will need to start playback on each deck manually.
36. STEREO LEVEL INDICATOR – Displays the audio level of the Program mix.
37. MASTER VOLUME – Adjusts the output volume of the Program mix.
38. ZONE VOLUME – Controls the audio level of the Zone output.
39. MONO / STEREO – Adjusts the Program mix for stereo or mono operation.
40. DOCK – Connect your iPod here. Gently rock the iPod back and forth over the connector when attaching or removing it.
41. DOCK ADJUSTER – Turn this knob accordingly so your docked iPod rests against the support.
42. iPod CONTROLS & JOG WHEEL – Functions as the controls for your iPod's menus and Touchwheel while it is plugged
into the mixer.
Note: When connecting microphones,
make sure the mic channel's gain knob
is at the lowest setting (or turn the mic
channel off) before connecting it.
5