Precautions In Use; Installation Location; Maintenance; Regarding Condensation - TAD D1000MK2 Manual De Instrucciones

Precautions in use

installation Location

For installation, select a stable location near the television or
stereo system with which the unit will be used.
to ensure long product life, avoid installing this
unit in the following locations:
• Locations exposed to direct sunlight
• Humid or poorly ventilated areas
• Areas of extreme temperatures
• Areas with vibration
• Dusty or smoky areas
• Areas exposed to grease fumes, steam or heat
(such as a kitchen)
Do not place objects on top of the unit
Do not place objects on top of the TAD-D1000MK2.
to prevent adverse affects of heat
Do not install the TAD-D1000MK2 on top of amplifiers or
other components that generate heat. When installing in
a rack, try by all means to install the TAD-D1000MK2 in a
position below amplifiers or other components that generate
heat.
turn off power when not in use
Depending on the signal condition of television broadcasts,
if the television is turned on when the TAD-D1000MK2 is
already on, a noise may appear on the television screen.
Audible noise may likewise occur when listening to the
radio when TAD-D1000MK2 is already turned on. This
phenomenon does not indicate a malfunction of either the
television, radio tuner, or the TAD-D1000MK2. In this event,
turn off the power to the TAD-D1000MK2.
CAUTION
The line output volume of the unit is set to the default value (30) by factory default.
When using the line output volume function of the product and directly connecting to a power amplifier, be sure to make
the connection only after setting the volume to "0" (zero).
(1) Press the <VOL − button> on the unit to decrease the line output volume.
(2) Press the <VOL − button> again to set it to "0" (zero).
If a direct connection to a power amplifier is made with the line output volume set high, an excessively loud sound may be
produced and the speakers or your hearing may be damaged.
6
Moving the taD-D1000MK2
If you must move the TAD-D1000MK2, first remove any disc
loaded and close the disc tray. Press the main unit's 
power button (or the remote control unit's  DISC PLAYER
button) so that the [OFF] indicator in the display goes out,
then unplug the power cord. Never move the unit with a disc
loaded, since damage may result.
caution for when the unit is installed in a rack
with a glass door
Do not press the h OPEN/CLOSE button on the remote
control to open the disc tray while the glass door is closed.
The door will hamper the movement of the disc tray, and the
unit could be damaged.

Maintenance

To clean the TAD-D1000MK2, use a polishing cloth to gently
wipe the unit's surface to remove dust. If the surface is
extremely dirty, wipe with a soft cloth dipped in neutral
cleanser diluted five to six times with water and wrung out
well. Do not use volatile chemicals such as paint thinner or
benzenes, as these may corrode the surface of the panels.
Do not use sprays such as insecticides around the TAD-
D1000MK2. If you plan on using a chemical cleaning cloth,
read the precautionary statements of the chemical cleaning
cloth before using.

regarding condensation

During the winter or cool seasons, condensation may form
inside the player if it is brought into a warm room from
outside or other cold location, or if the temperature of the
room where the player is installed is raised too quickly. When
condensation forms inside the player, it may not operate
properly or at all. In this event, turn on the unit's power and
allow it to stand for 1 to 2 hours so that the condensation
evaporates as the player acclimatizes to the room's
temperature, and the unit will become playable again.
Condensation may also form in the summer if a room's air
conditioner is directed directly at the TAD-D1000MK2. In
this event, change the location of the player away from the
airstream of the air conditioner.