MoJack EZ Max Instrucciones Para El Montaje Y La Operación página 8

Operating Instructions
STEP 9
Strapping Front Mower Tires to Wheel Pads
• Secure the front mower tires to the Wheel
Pads using the Safety Straps. Secure the
hook on the Safety Strap to the Wheel Pad
Slot.
The Safety Strap hook should always be
facing upward.
• Extend the Safety Strap over the top of tire.
• Insert the Wheel Support Rod through one
hole on the Wheel Pad, through the loop on
the Safety Strap and through the other side of
the Wheel Pad. Secure with Large Hair Pin.
• Squeeze the metal buckle and pull end of
strap to tighten the Safety Straps over the top
of the tires to secure mower to Wheel Pads.
NOTE: Inspect Safety Strap for wear before
each use.
Always secure front mower tires with
enclosed safety straps.
STEP 10
Raising the Mower
• Raise the mower by rotating the Crank Handle clockwise.
• See Step 15 for raising the mower with drill attachment.
Do not exceed the lifting capacity of 450 lbs.
(204 kg) front end weight. If you have a question
regarding weight of your machine, please contact
MoJack at 1-877-575-3173.
If the lift Tower is leaning while lifting or lowering
the mower, this indicates an overload condition.
REMOVE THE MOWER IMMEDIATELY.
The jack must be used on a solid level surface.
Mower deck must be raised to highest setting.
The engine must be turned off and key removed.
The mower must be in neutral when raising or
lowering to allow the wheels roll as the mower is
raised or lowered.
The parking brake must be off during this step.
Always use attached safety straps. The Safety Straps must be firmly tightened.
MoJack EZ Max Lift
Safety Strap
Wheel
Support
Rod
Wheel Pad
Slot
Wheel
Support Rod
Safety Strap
Loop
Safety
Strap
Wheel Pad
Slot
14
STEP 11
Raising Lift Arm to Locking Position
• Raise the Lift Arm until the Carrier Locking Handle drops into one of
the two Tower Holes.
• The Carrier Locking Handle automatically drops into the
Tower Holes as the Carrier passes the Tower Holes when raising.
NOTE: When lowering the Lift Arm, the Carrier Locking Handle must
be held out by the operator until it clears the bottom Tower Hole.
NOTE: The MoJack EZ Max is equipped with a clutch to protect
itself from accidental damage. If the Carrier Locking Handle is not
disengaged when lowering, the clutch will release the Crank Handle
from the screw and rotate freely. To re-engage the Crank Handle,
turn clockwise for a few turns.
Hair Pin
STEP 12
Preparing the Mower for Service
• Place wheel chocks (not included) behind the back tires of the mower.
• Apply the parking brake on the mower.
• The Carrier Locking Handle must be locked into one of the
two Tower Holes.
STEP 13
Lowering the Mower
• Remove wheel chocks.
• Release the parking brake.
• Mower must be in neutral or hydraulic drive disengaged.
• Pull and hold the Carrier Locking Handle out and turn
the Crank Handle counter clockwise until Wheel Pads
are firmly on the ground. The Carrier Locking Handle
must be pulled out until it clears the bottom Tower
Hole. It may be necessary to raise the Carrier slightly
to allow the Carrier Locking Handle to be pulled out.
NOTE: The MoJack EZ Max is equipped with a clutch
to protect itself from accidental damage. If the
Carrier Locking Handle is not disengaged when lowering,
the clutch will release the Crank Handle from the screw
and rotate freely. To re-engage the Crank Handle,
turn clockwise for a few turns.
MoJack EZ Max Lift
Operating Instructions
Wheel Chock
15
Tower Holes
Carrier
Locking
Handle
Tower Holes
Carrier
Locking
Handle