Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Setting the required pressure (fig. D)
Warning! Do not leave the inflator running
unattended. It could burst tires or other items.
Note: You must set the automatic shut-off feature
before the unit will operate.
•
To switch between the different units (kPa,
psi or bar), press buttons 8 & 9 at the same
time until the required units are displayed.
•
Press and hold button 8 or 9 for 3 seconds
until the display flashes.
•
While the display is flashing press the - or +
buttons (8 & 9) until the required pressure is
displayed.
•
After 3 seconds the display will flash and
return to a reading of "0.0". This is normal.
•
Connect the universal valve adaptor and
accessories, if required, to the item to be
inflated, making sure that the lever of the
valve adaptor is in the down position to lock
it in place.
•
To turn the inflator on, press the on/off
switch (5) to the I position.
•
When the item to be inflated has reached
the preset value the unit will automatically
turn off.
•
To turn the inflator off press switch (5) to the
0 position.
•
Remove the valve adaptor or accessory from
the inflated item and the 12 Volt adapter (6)
from your vehicle's 12 Volt accessory socket.
Note
: If the 12 Volt adapter is removed from the
vehicles 12 Volt accessory socket, all settings will
be lost and will need to be re-entered following
the instructions under the heading 'Setting the
required pressure.
Operating the area light
•
To operate the area light (1), make sure that
the 12 Volt adaptor (6) is plugged into the
vehicle's 12 Volt accessory socket.
Note: Make sure that your 12 Volt accessory
socket is live. On some vehicles the accessory
socket may only become live when the ignition
key is in the accessory position.
•
To turn the area light on, press the area light
on/off switch (7) located on the side of the
unit to the I position.
•
To turn the area light off, press the area light
on/off switch (7) located on the side of the
unit to the 0 position.
14
To replace the bulb (fig. E)
Warning! Make sure that the 12 Volt adaptor is
not connected before starting this procedure.
•
Remove the screw (10) from the top of the
lens cover (12).
•
Pull the lens cover (12) down using the tab
(11) to get access to the bulb (13).
•
To remove the bulb, push in and turn
clockwise (fig. E).
•
Replace the bulb (13) with a one of the same
type and wattage (12V/5W).
•
Fit the lens cover (12) and secure with the
screw (10).
Using your inflator as a pressure gauge
•
Make sure that the unit is powered as
described in the section 'Operating the
Inflator'.
•
Connect the universal valve adaptor and
accessories if required to the item to be
inflated making sure that the lever of the
valve adaptor is in the down position to lock
it in place.
•
The display will now show the actual
pressure value in the item.
Maintenance
Your Black & Decker corded/cordless appliance/
tool has been designed to operate over a long
period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on
corded/cordless power tools:
•
Switch off and unplug the appliance/tool.
•
Or switch off and remove the battery from
the appliance/ tool if the appliance/tool has a
separate battery pack.
•
Or run the battery down completely if it is
integral and then switch off.
•
Unplug the charger before cleaning it. Your
charger does not require any maintenance
apart from regular cleaning.
Regularly clean the ventilation slots in your
appliance/tool/ charger using a soft brush or dry
cloth.
Regularly clean the motor housing using a damp
cloth. Do not use any abrasive or solvent-based
cleaner.
Regularly open the chuck and tap it to remove
any dust from the interior (when fitted).
Publicidad
Tabla de contenido
Solución de problemas
