Electric Safety - Black and Decker ASI200 Manual De Instrucciones

Inflador multiuso
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

signs of damage, ageing and wear.
Do not use the appliance if the power supply
cord or mains plug is damaged or defective
(where applicable).

Electric Safety

This tool is double insulated; therefore
no earth wire is required. Always check
that the power supply corresponds to the
voltage on the rating plate.
Electrical safety can be further improved by using
a high sensitivity (30mA / 30mS) Residual Current
Device (RCD). If the power cord is damaged,
it must be replaced by the manufacturer,
authorized Black & Decker Service Center or an
equally qualified person in order to avoid damage
or injury. If the power cord is replaced by an
equally qualified person, but not authorized by
Black & Decker, the warranty will not be valid.
Labels on tools
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Do not expose the appliance to rain or high
humidity
Before performing maintenance or cleaning on
the appliance, unplug the supply cord.
Do not leave the inflator unattended.
Features
1.
Area light
2.
Pressure gauge
3.
Storage location for air hose and 12 Volt adaptor
4.
Air hose with universal valve adaptor
5.
On/off switch
6.
12 Volt adaptor
7.
Area light on/off switch
Use
Air hose and cord storage (fig. A)
Wrap the dc cord around the base of the unit and
then put the air hose (4) and the 12 Volt adaptor (6)
into the storage location (3).
Fitting the accessories (fig. B and C)
Your inflator is supplied with the standard tapered
nozzles and the needle inflator nozzle, these are
located on the base of the unit (fig. C).
To use the universal valve adaptor, make
sure that the lever is in the up position.
Place the valve adapter over the stem of the
inflation needle or tapered nozzle (fig. B).
Press the lever on the valve adapter down to
lock it in place.
Place the inflation needle or tapered nozzle
into the item to be inflated.
Note: Always make sure that the lever is in the up
position when not in use.
Operate your Inflator only with the universal valve
adaptor or with the included nozzles.
Note: Make sure that the universal valve adaptor
is firmly locked in place before turning the
Inflator on.
Many inflatables have an internal flap that
prevents air loss during inflation. Unless this flap
is displaced by the nozzle the inflatable will not
inflate. Push the nozzle firmly into the valve to
make sure that you push this flap out of the way.
Store the inflation needle inside one of the
tapered nozzles and snap the tapered nozzles
into the storage slots located on the bottom of the
Inflator (fig. C).
Warning! Excessive air pressure may cause a
hazardous risk of bursting or personal injury.
Check the manufacturer's maximum pressure
rating for the items being inflated.
Note: If the pressure rating for the item being
inflated is above 100 psi, note that the maximum
run time is 10 minutes, leave to rest for 20
minutes before re-use.
Operating the inflator
Warning
! Do not operate the inflator when the
car engine is running.
Note
: Make sure that your 12 Volt accessory
socket is live. On some vehicles the accessory
socket may only become live when the ignition
key is in the accessory position.
To power the display
Always fully extend the 12 Vdc cord before
each use.
Connect the 12 Volt adaptor (6) into the
vehicle's 12 Volt accessory socket.
To enable the inflator to operate you must
set the required units (psi, bar or kPa) and a
pressure valve.
13

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido