Wet Vacuum Cleaning; Blowing Operation; Maintenance& Filter Cleaning - EWT AquaVac COMPACT 10P Instrucciones De Uso

WET VACUUM ClEANING

WARNING: BE SURE TO READ, UNDERSTAND, AND APPlY INFORMATION, ENTITlED 'SAFETY INSTRUCTIONS &
WARNINGS' . DO NOT VACUUM IN AREAS WITh FlAMMABlE GASES, VAPORS, OR EXPlOSIVE DUSTS IN ThE AIR.
FlAMMABlE GASES OR VAPORS INClUDE BUT ARE NOT lIMITED TO; lIGhTER FlUID, SOlVENT TYPE ClEANERS,
OIl-BASE PAINTS, GASOlINE, AlCOhOl OR AEROSOl SPRAYS. EXPlOSIVE DUSTS INClUDE BUT ARE NOT lIMI-
TED TO; COAl, MAGNESIUM, GRAIN OR GUN POWDER.
TO REDUCE ThE RISK OF hEAlTh hAZARDS FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIAlS.
WARNING: DO NOT PlUG IN POWER CORD TO POWER OUTlET, MAKE SURE PlUG IS DISCONNECTED BEFORE
ASSEMBlING ThE WET/DRY VAC
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Remove reusable cloth filter, then carefully install the foam sleeve filter over the filter cage and place the power head back
on the container. (fig.2) See filter installing instructions on page 32.
DO NOT USE ThE REUSABlE ClOTh FIlTER FOR lIQUID VACUUMING.
3. Fit the desired nozzle to the vacuum hose. (fig.3)
4. Verify that the switch is in the 'O' OFF position before plugging the power cord into the outlet. (fig.4)
5. Turn the motor on by flipping the switch to the 'I' ON position. (fig.5)
6. After use, empty the container, clean and dry the inside and outside before storage. (fig.6)
IMPORTANT!
When vacuuming large quantities of liquids, do not immerse the nozzle completely in the liquid; leave a gap at
the tip of the nozzle opening to allow air inflow. The machine is fitted with a float valve that stops the suction action when the
container reaches its maximum capacity. You will notice an increase in motor speed. When this happens, turn off the machine,
disconnect from power supply, and drain the liquid into a suitable receptacle or drain. To continue vacuuming, refit the contai-
ner with the drain cap. After wet vacuuming, turn the machine off and remove plug from power supply. Empty the container,
.
clean and dry the inside and outside before storage
REMEMBER!
The foam filter must be removed after wet vacuuming, and a reusable cloth filter must be installed before dry
vacuuming again.
30
All manuals and user guides at all-guides.com

BlOWING OPERATION

This Wet/Dry Vac has blowing capabilities. To use the blower feature follow the instructions listed.
WARNING: AlWAYS WEAR SAFETY GOGGlES COMPlYING WITh ANSI Z87.1 (OR IN CANADA, CSAZ94.3) BEFORE
USING BlOWER.
WARNING: KEEP BYSTANDERS ClEAR FROM BlOWING DEBRIS.
WARNING: WEAR A DUST MASK IF BlOWING CREATES DUST ThAT MIGhT BE INhAlED.
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Make sure the container is empty before using as a blower.
3. Remove hose from the vacuum port.
4. Insert the larger end of the hose into the blowing port on the backside of the power head. (fig.2)
5. Ensure the power switch is turned off and plug into the power supply. (fig.3 & 4)
6. Before turning on the vac, firmly hold loose end of the hose. Turn the motor on by flipping the switch to the 'I' ON position.
(fig.5)
MAINTENANCE & FIlTER ClEANING
1. Verify that the power cord is disconnected from the outlet. (fig.1)
2. Disconnect the hose from the vacuum. (fig.2)
3. Undo the latches and remove the power head from the container. (fig.3 & 4)
4. Clear all dirt or debris from the container and hose. (fig.5)
For filter changing and maintenance see instructions on page 32.
IMPORTANT!
Clean or change the dust filter regularly for best performance. ALWAYS USE DUST FILTER FOR DRY VACUUMING.
If the machine is used with out the dust filter, the motor will burn out and the warranty will be voided. Always keep spare filters
on-hand.
NOTICE!
The filter included is made of high quality material designed to stop small dust particles. The filter should be used
for dry pick-up only. A dry filter is necessary to pick up dust. If the dust filter is wet, it will clog quickly and be very difficult to
clean. Handle the filter carefully when removing it for cleaning and replacing it. Check the filters for tears or small holes, a small
hole can let dust pass through and out of the cleaner. Do not use a filter with holes or tears, replace it immediately.
WARNING: AlWAYS DISCONNECT ThE PlUG FROM ThE POWER OUTlET BEFORE REMOVING ThE POWER hEAD
FROM CONTAINER.
GB
31