Synchronize The Door Control - Craftsman 139.3043 Manual Del Propietário

Features (Continued)
USING YOUR GARAGE DOOR OPENER
The garage door opener can be activated through a wall-mounted
door control, remote control, wireless keyless entry or
AssureLink™ accessory.
When the door is closed and the garage door opener is activated
the door will open. If the door senses an obstruction or is
interrupted while opening the door will stop. When the door is in
any position other than closed and the garage door opener is
activated the door will close. If the garage door opener senses an
obstruction while closing, the door will reverse. If the obstruction
Door Control

SYNCHRONIZE THE DOOR CONTROL

To synchronize the door control to the garage door opener,
press the push bar until the garage door opener activates (it
may take up to 3 presses). Test the door control by pressing the
push bar, each press of the push bar will activate the garage
door opener.
USING THE DOOR CONTROL
Push Bar
Navigation
Buttons
LIGHT Button
Push Bar
Press the push bar to open or close the door.
Light Button
Press the LIGHT button to turn the garage door opener lights on
or off. When the lights are turned on they will stay on until the
LIGHT button is pressed again, or until the garage door opener is
activated. Once the garage door opener is activated the lights will
turn off after the specified period of time (the factory setting is
4-1/2 minutes). The LIGHT button will not control the lights when
the door is in motion. The duration of the light timing can be
adjusted using the door control.
Navigation Buttons
Use the navigation buttons to make selections and program
features.
Screen
The screen will display the time and temperature until the menu
button is pressed, and then it will display the menu options. If
there is a problem with the garage door opener the screen will
display the Diagnostic Code. Refer to the Troubleshooting section.
interrupts the sensor beam the garage door opener lights will
blink 10 times. However, you can close the door if you hold the
button on the door control or keyless entry until the door is fully
closed. The safety reversing sensors do no effect the opening
cycle.
The safety reversing sensor must be connected and aligned
correctly before the garage door opener will move in the down
direction.
The following features are accessible through the screen using
the navigation buttons on the Smart Control Panel:
LEARN A DEVICE
Any compatible remote controls, wireless keyless entry, or
AssureLink™ accessories can be programmed to the garage door
opener by accessing the menu and using the navigation buttons
on the Smart Control Panel.
Lock
The LOCK feature is designed to prevent activation of the garage
door opener from remote controls while still allowing activation
Screen
from the door control and keyless entry. This feature is useful for
added peace of mind when the home is empty (i.e. vacation).
Motion
Sensor
Timer-to-Close (TTC)
DO NOT enable TTC if operating a one-piece door. TTC is to be
used ONLY with sectional doors.
Factory default is set to off. TTC can be set to automatically close
your garage door from the fully open position after a specified
period of time (1, 5, 10 minute intervals). The Smart Control Panel
also has a custom setting up to 99 minutes. The garage door
opener will beep and the lights will flash before closing the door.
The screen on the door control will display the status of the TTC
such as time to close, paused, or an error. If the door encounters
an obstruction while closing, the garage door opener will make a
second attempt to close the door. If the obstruction has not been
cleared after the second attempt, the garage door opener will
reverse open, stop and WILL NOT close until the obstruction has
been cleared. TTC WILL NOT work if the garage door opener is
operating by battery power or if the safety reversing sensors are
misaligned. This feature is NOT intended to be the primary
method of closing the door. A keyless entry should be installed
in the event of an accidental lock out when using this feature.
AUTOMATIC LIGHT
Motion Sensor
Factory default is set to on. This feature will automatically turn on
the garage door opener lights when motion is sensed. The lights
will come on for the set period of time, then shut off.
If using the garage door opener light as a work light disable the
Automatic Light Feature, otherwise the light will turn off
automatically if you are beyond the range of the sensor.
Light Feature
The lights will turn on when someone enters through the open
garage door and the safety sensor infrared beam is broken.
33