Installation - Thetford SANICON TURBO 600S Manual Del Propietario Y Instalación

Overview
Follow the instructions below to attach the SANICON® 600 to the
RV coach.
Read and understand the warnings listed in this docu-
NOTICE AVISO DANGER AVIS
! ! ! ! ATTENTION ATENCIÓN CAUTION
ment before you install, operate, or service this system. If
ATTENTION ATTENTION ATTENTION
you do not obey these warnings there is a risk of property
loss, injury, or electrocution. Do not make any changes to
this unit as this could result in property damage, injury, or
electrocution.
Thetford Corporation accepts no responsibility or liability for
damage to equipment, injury, or death that may result from the
system's improper installation, service, or operation.
Thetford Corporation recommends that plumbing and electrical
work be performed by a licensed tradesperson. Local permit and
code compliance is required.
Contents
■ (1x) SANICON® Turbo 600S Assembly - with OT (over-
temperature) protected pump
■ (2x) Mounting Brackets
■ (1x) 3" Inlet Hose
■ (1x) Hose and Nozzle Assembly with nozzle caps
■ (1x) Switch Box Assembly
■ (1x) Fuse Holder
■ (1x) 35 AMP Fuse
■ (2x) Electrical Connectors
■ (1x) Owners & Installation Manual
■ (2x) Labels with serial #
Required Materials (Not Provided)
■ Plumbing and End Caps (if necessary)
■ Wiring
■ Mounting Hardware
■ Schedule 30, 40, 80, or DWV rated hard pipe fi ttings or
minimum 10 PSI fl exible pipe rating for pressure side of
pump.
97573 Rev. E (01/08/18)

Installation

General Guidelines
Gray water bypass can be achieved by plumbing the discharge
line in a manner that gravity can allow liquid to fl ow to the hose
with no upward plumbing.
All systems rely on gravity to move the liquid waste to the pump;
therefore, make sure that the pump inlet is mounted below the RV
holding tank.
Each assembly comes with two labels. One label should be
placed in the hose compartment; the other should be placed in the
Owner's Manual.
■ If black and gray tanks are heated, treat SANICON® Turbo
600S in same manner.
■ It is important to plumb hose avoiding sharp angles or
bends during use or storage.
■ Placement of the hose connection MUST be serviceable by
the customer.
Warnings and Cautions
Read and understand the warnings and cautions listed in this
document before you install or operate this unit.
NOTICE AVISO AVIS
! CAUTION
NOTICE AVISO ATENCIÓN CAUTION DANGER AVIS
! ! ! ! ATTENTION
ATTENTION ATTENTION ATTENTION
Thermal Cut-Off Switch
Because SANICON® Turbo pumps are designed for intermittent
duty, the pump contains a thermal cut-off switch for your safety.
Typical run time is 15-20 minutes of pumping before the pump
turns itself off and needs to cool for at least 20 minutes before the
thermal cut-out resets and the pump can run again.
■ If the pump is run immediately after a thermal reset, it will run
for approximately 5-8 minutes.
■ If allowed to cool for several hours it will run the full 20 min-
utes.
Questions?
If you have any questions or need assistance, please contact
Technical Support at 1-800-444-7210, available Monday through
Friday 8 a.m. to 6 p.m., Eastern Standard Time.
2
Do not make any changes to this unit, as this could result
in property damage or injury.
Gray and black water tanks MUST BE COMPLETELY
FREE FROM DEBRIS before installing and operating the
pump. Failure to comply with this warning could result in
a voided product warranty and equipment failure.
The installation site of the pump MUST be able to support
a minimum of 30 pounds.
The pump is suitable for indoor and outdoor use. The
switch box is intended for indoor use only and must be
protected against water.
SANICON
®
Turbo - Model 600S