Thetford SANICON TURBO 600S Manual Del Propietario Y Instalación página 8

Operation, cont'd.
Empty Gray Water Tank(s)
Refer to Fig. 1 and Fig. 4.
1. Make sure universal nozzle (
dump station! Refer to "Attach to Dump Station" procedure.
TIP For Cleaner Storage: Emptying black water tank fi rst,
NOTICE
allows gray water to clean the system.
2. Open gray water tank gate valve (
3. Use ( ) to turn pump on.
K3
4. Do not leave unit unattended.
TIP: The hose expands as fl uid moves to dump station
NOTICE
and contracts when tank is empty.
5. Use switch box ( K3 ) to turn pump off.
6. Close gray water tank gate valve
7. Repeat Steps 2-6 for secondary gray tanks.
Gray water bypass is possible if the discharge
NOTICE
plumbing does not fl ow upward.
Prepare Hose For Storage
Refer to Fig. 1 and Fig. 4.
1. Make sure pump is off.
2. Drain hose ( ) by holding at a sloped angle to direct excess
K2
water into the dump station.
TIP For Faster Draining: Leave gray gate valve
NOTICE
open allowing hose to vent and expediting the process.
3. Disconnect nozzle (
K2.2
4. Install cap(s) ( K2.3, K2.4
5. Return hose to coach hose compartment (
connected to coach.
Helpful Hints
■ Additional hoses can be purchased from Thetford and used
to extend the length of the discharge hose. Connect the
hoses using 1.5" (3.8 cm) barbed coupling with clamp.
■ If you wish to extend the evacuation hose, connect a .75"
(1.9 cm) inner diameter garden hose to the end of the
nozzle.
A longer evacuation hose reduces fl ow rate.
NOTICE
■ Before storing the hose, make sure that all liquid has drained from
the hose.
Gray water bypass is possible if the discharge
NOTICE
plumbing does not fl ow upward.
Inspect pump connection to the RV annually.
NOTICE
97573 Rev. E (01/08/18)
K2.2 ) is securely attached to
4A ).
.
(4A)
) from dump station.
).
); leave hose
4B
Obstruction Removal
Refer to Fig.1 and Fig. 4.
NOTICE
1. Make sure all contents have been drained from system.
AVISO AVIS
! ! ! ! NOTICE ATTENTION ATENCIÓN DANGER CAUTION
ATTENTION ATTENTION ATTENTION
2. Disconnect the power by removing the pump fuse or discon-
necting the battery.
3. Make sure all gate valves (
NOTICE
4. Locate 3" inlet hose
to the pump.
AVISO AVIS
! ! ! ! NOTICE ATTENTION DANGER ATENCIÓN CAUTION
ATTENTION ATTENTION ATTENTION
5. Remove the pump from the 3" inlet hose (
6. Remove the obstruction.
7. Insert the pump inlet into 3" inlet hose
clamp.
AVISO AVIS
! NOTICE CAUTION
8. Reconnect the power.
(4A)
9. Operate system using gray water; check for leaks.
Winterizing
Refer to Fig. 1 and Fig. 4.
1. Ensure all tanks are empty.
2. Pour RV antifreeze into the empty black water tank.
3. Turn on pump.
NOTICE
4. Run pump until the antifreeze begins to discharge from
universal nozzle (
5. Turn pump switch to the Off position.
6. Drain hose (
excess water; return hose to storage position.
8
Be sure to have container available for capturing system
fl uid!
Turn off power and remove pump fuse. Once the ob-
struction is removed, there is potential injury to hands or
fi ngers in the path of the impeller if the power is on!
4A ) are closed.
Plumbing from the discharge port (
be disconnected.
(K7) and loosen the hose clamp closest
Do NOT remove pump housing. Obstruction MUST be
removed through inlet.
K7
Do not overtighten the hose clamp when adjusting the
hose length, as it may damage the hose.
Be sure to have container available for capturing system
fl uid!
).
K2.2
K2 ) by holding at a sloped angle to remove
SANICON
) may need to
K1.1
).
K7
) and tighten hose
®
Turbo - Model 600S