English - Fellowes Saturn 3i A4 Manual De Instrucciones

ENGLISH

E
LAMINATOR CONTROLS
A On / off switch
B Laminator feed sensor
C Pouch selection buttons (
D Release lever (
CAPABILITIES
Performance
Format
Entry width
Pouch thickness (min)
Pouch thickness (max)
Warm up time (estimate)
Cool down time
Lamination speed (+/- 5%)
Number of rollers
Ready indication
Release lever
Clear Path / Anti-jam engine
IMPORTANT SAFETY INSTRUCTIONS - KEEP FOR FUTURE USE
- The machine is for indoor use only. Plug the machine into an easily accessible socket.
- To prevent electrical shock - do not use the appliance close to water, do not spill water on to the appliance, power cord or wall socket.
DO ensure the machine is on a stable surface.
DO test laminate scrap sheets and set the machine before final laminations.
DO remove staples and other metal articles prior to laminating.
DO keep the machine away from heat and water sources.
DO turn off the machine after each use.
DO unplug the machine when not in use for an extended period.
DO use pouches designed for use at the appropriate settings.
DO keep away from pets, while in use.
DO ensure self-adhesive pouches are only used with the cold setting.
FEATURES & TIPS
Lamination Feed Sensor
When the machine senses a pouch has been mis-fed and has not gone
completely through the machine in a normal operating time, the Lamination
Feed Sensor LED will blink. Use the release lever located at the rear of the
machine to remove the laminate. A beep will sound if a pouch is left on the exit
tray to alert the user to remove the pouch.
Auto Shut Off
If the machine is not active for 30 minutes, the Auto Shut Off function will place
the machine into standby mode. All LEDs will be dimly blinking. To operate the
machine, press any button or cycle the power switch.
'Release' function
To remove or re-align a pouch during lamination, activate the release lever
located at the rear of the machine. The pouch can only be removed from the
entry slot when the lever is activated.
4
, 80mic, 100mic, 125mic)
)
A3 or A4
A3 = 318mm
A4 = 240mm
75 microns
125 microns
1 minute
60-90 minutes
approx. 30cm/min (fixed speed)
2
Light & beep
Yes
Yes
E Pouch / document entry slot
F Entry support shelf
G Pouch / document exit
Technical Data
Voltage / Frequency / Current(Amps)
Wattage
Dimensions (HxWxD)
Net weight
Max document thickness
(laminating capacity)
DO NOT leave the power cord in contact with hot surfaces.
DO NOT leave power cord hanging from cupboards or shelves.
DO NOT use appliance if the power cord is damaged.
DO NOT attempt to open or otherwise repair the machine.
DO NOT exceed the machines quoted performance.
DO NOT allow children to use this machine without adult supervision.
DO NOT laminate sharp or metal objects (eg: staples, paper clips).
DO NOT laminate heat-sensitive documents (eg: tickets, ultrasounds etc) on hot settings.
DO NOT laminate with self-adhesive pouches on hot settings.
DO NOT laminate an empty pouch.
For best results, use Fellowes ® brand pouches:
Enhance 80, Impress 100.
For self-adhesive (cold pouches) only use the cold setting.
This machine does not need a carrier to laminate. It is a carrier-free mechanism.
Always put the item to be laminated into the appropriate sized pouch.
Always test laminate with a similar size and thickness before final process.
Prepare pouch and item for lamination. Place item within pouch centred and
touching the leading sealed edge. Ensure the pouch is not too large for the item.
If required, trim excess material from around the item after lamination and
cooling.
When working with different pouch thickness' (temperature settings) it is
recommended to first start with the thinnest pouches.
A3 = 220-240V AC, 50/60Hz, 3.4A
A4 = 220-240V AC, 50/60Hz, 3.4A
A3 = 750 Watts
A4 = 750 Watts
A3 = 105 mm x 532 mm x 146 mm
A4 = 105 mm x 436 mm x 139.2 mm
A3 = 2,3 kg
A4 = 1,8 kg
0.02" / 0.5mm