Troubleshooting; Technical Specifications - KlipXtreme Allure KLS-660 Manual De Instrucciones

c. Start streaming audio files directly from the source of choice.
d. Press and hold the button to play or pause the audio. Press this button shortly to go to the previous or
next track.
3. SD mode operation
TM
Recommendation: Use an SD™ card to enable audio playback from compatible files stored in an SD™ memory card.
a. First, connect an SD™ card to the SD™ port of the speaker.
b. The speaker will detect the SD™ card and play the audio files. If the SD™ card is not automatically detected,
press the MODE button to toggle through the different modes available until the preferred mode is found:
Line In, Bluetooth®, USB, SD , FM.
TM
c. Start streaming audio files directly from the source of choice.
d. Press and hold the button to play or pause the audio. Press this button shortly to go to the previous or
next track.
4. FM (radio) mode
1. Press the MODE button briefly to toggle through the available audio sources and select FM.
2. Press the PLAY/PAUSE button to start searching for radio stations automatically, in the radio frequency
range between 87.5 and 108.0 MHz. The unit will save the radio stations automatically in the available
channels.
5. How to use the recording feature
1. First, make sure to have a microphone connected and a compatible memory card or USB drive inserted in
order to activate the recording feature.
2. The unit will select the USB source as the default source to save the recording. In case there is no a USB
source inserted, the unit will select the SD
displayed on the screen.
3. Start recording, and when finished, briefly press the REC button again to stop and play the recording.
4. To delete a recording, first go to Rec. Play Mode and the unit will select the channels where the recordings
were saved. Pick the recording you wish to eliminate and press Delete.
VI. Advanced operation
Pairing the speaker with wireless devices
Note: Before installing this product, please make sure your device is compatible with Bluetooth®.
1. Enable the Bluetooth® feature on the selected source and set it to discover the wireless speaker.
2. Place your wireless device and the speaker not more than one meter away from each other.
3. Next, cycle to the Bluetooth® feature on the speaker by pressing the MODE button found on the media
panel and select it as the input source. The bt symbol blinks fast on the display to indicate that the
speaker has entered into the pairing mode.
4. Once the speaker appears listed under the newly found Bluetooth® devices (KLS-660) of your wireless
device, select it and wait a few seconds for pairing.
5. When pairing is successful, the bt symbol stops blinking indicating that the Bluetooth® is connected. If after
60 seconds the pairing process fails, please repeat steps 1 through 5 described above.
6. You can now start streaming audio through the speaker wirelessly from your favorite Bluetooth®- enabled
devices.
7. The speaker will re-pair automatically to the memorized device when the BT mode is selected on the
unit after being turn off and on again.
source as an alternative. Press the REC button until Rec is
TM
VII. Troubleshooting
Problem Possible cause
1: There is no input sound source connected
The speaker is On but
2: Volume knob is in the lowest position
there is no sound
3: USB/SD is not connected
TM
Sound is distorted
1: The volume is too loud
2: Audio file error
There is no sound coming
1: The song format is not compatible with
from the USB/SD files
TM
the file Format.
2: The USB/SD audio source is not inserted properly
TM
There is no sound coming
1: The microphone jack is not fully plugged in
from the microphone
2: The microphone switch is not on
3: Microphone volume is in the lowest position
Problem to reproduce
1:The unit doesn't search radio channels or the
an FM station
transmission is not clear
There is noise/interference 1:The wired microphone is used too close
Coming from the speaker to the speaker
2:The wired microphone switch is on but the
Microphone is not in use
3: The microphone volume is too loud
4: The mobile phone is too close to the speaker
5: There are other devices too close to the speaker
1: Bluetooth connection is disconnected
®
connection
®
Bluetooth
2: Bluetooth connection is established but
®
fails
there is no sound
3: Bluetooth connection effective distance is
®
not enough

Technical specifications

MPN
Device
Type
Reference RMS power
Maximum power output (PMPO)
AC Input
Speaker
DC input
Buttons
Driver unit
Subwoofer
Reference RMS power
Frequency
Microphone
Impedance
Sensitivity
Signal to noise ratio
THD
Solution
1: Connect an input sound source
2: Adjust the volume
3: Insert a USB/ SD audio source
TM
1: Turn the volume down
1. a: Adjust the Bass/Treble frequencies
and the main volume
2: Check and change the audio file
1: The file should be a MP3/WMA music file
1.a: Check the USB size (if the file is bigger
than 2Gthe unit will take longer to
reproduce the file)
2: Insert the USB/SD audio source properly
TM
1: Plug the microphone jack correctly
2: Turn on the microphone
3: Adjust the volume of the microphone
1: The FM antenna is not properly expanded
2: Try to position the antenna in a different angle
4: Try the "Auto scan" function.
1: Do not let wired microphones point directly
at the speaker
2: Turn off wired microphone if not in use
3: Turn down the volume of the microphone
4: Keep the mobile device away from the
speaker during calls
5: Keep the speaker away from other sources
of interference
1: Find the right device name (KLS-660)
or press and hold the the REPEAT button
to restore Factory settings
2: Confirm that you are connected to the
right device (KLS-660)
3: Try to keep away from barriers, such as
walls, glass etc.
KLS-660
Loudspeaker system
120W
1200W
100V-240V, 60/50Hz
12V
7 buttons (Mega Bass, Menu, Play/Pause, Mode, Previous,
Next, Volume +/-)
2x 8in at 3 (40W each)
80W
20Hz-6kHz
3 , ±10 %
88dB, ±2dB
≥65dB
1kHz 0dB (±10%)