Milwaukee 5337-20, 5337-21 Manual Del Operador página 11

mainTenance
To reduce the risk of injury, always unplug your tool before per-
forming any maintenance. Never disassemble the tool or try to do
any rewiring on the tool's electrical system. Contact a milWaukee
service facility for ALL repairs.
Maintaining Tools
Keep your tool in good repair by adopting a regular maintenance pro-
gram. Before use, examine the general condition of your tool. Inspect
guards, switches, tool cord set and extension cord for damage. Check
for loose screws, misalignment, binding of moving parts, improper
mounting, broken parts and any other condition that may affect its safe
operation. If abnormal noise or vibration occurs, turn the tool off im-
mediately and have the problem corrected before further use. Do not
use a damaged tool. Tag damaged tools "DO NOT USE" until repaired
(see "Repairs").
Under normal conditions, relubrication is not necessary until the motor
brushes need to be replaced. After six months to one year, depending on
use, return your tool to the nearest MILWAUKEE service facility for the
following:
• Lubrication
• Brush inspection and replacement
• Mechanical inspection and cleaning (gears, spindles, bearings,
housing, etc.)
• Electrical inspection (switch, cord, armature, etc.)
• Testing to assure proper mechanical and electrical operation
Maintaining Hammer Chisels
Through normal use, the shank of the chisel can "mushroom" over and cause
the chisel to become stuck inside the hammer. To prevent this from happen-
ing, periodically remove the chisel from the tool and inspect the shank. If the
shank starts to "mushroom", have the chisel refurbished or replaced.
Brush Replacement
These MILWAUKEE hammers are will automatically shut off when the
brushes need to be replaced. Return your tool to the nearest MILWAUKEE
service facility for repairs.
Service Indicator Light
These MILWAUKEE Hammers feature a service indicator light. When the
red light turns on, the tool is in need of servicing. Return your tool to the
nearest MILWAUKEE service facility for service.
NOTE: When the service light comes on, the tool will continue to run for a
few hours and then the motor will shut off.
To reduce the risk of injury, electric shock and damage to the tool,
never immerse your tool in liquid or allow a liquid to flow inside
the tool.
Cleaning
Clean dust and debris from vents. Keep the tool handles clean, dry and
free of oil or grease. Use only mild soap and a damp cloth to clean your
tool since certain cleaning agents and solvents are harmful to plastics and
other insulated parts. Some of these include: gasoline, turpentine, lacquer
thinner, paint thinner, chlorinated cleaning solvents, ammonia and house-
hold detergents containing ammonia. Never use flammable or combustible
solvents around tools.
Repairs
If your tool is damaged, return the entire tool to the nearest service center.
Warning
Warning
accessories
To reduce the risk of injury, always unplug the tool before attach-
ing or removing accessories. Use only specifically recommended
accessories. Others may be hazardous.
For a complete listing of accessories refer to your MILWAUKEE Elec-
tric Tool catalog or go on-line to www.milwaukeetool.com. To obtain a
catalog, contact your local distributor or a service center.
Thick Wall Carbide-Tipped Core Bits
Core body with Guide Plate and Centering Pin
Diameter Drilling Depth
1-1/2" 4-1/16"
1-3/4" 4-1/16"
2" 4-1/16"
2-1/2" 4-1/16"
3" 4-1/16"
3-1/2" 4-1/16"
4" 4-1/16"
5" 4-1/16"
6" 4-1/16"
NOTE: Use MILWAUKEE core bits Cat. No. 48-20-5125 through 48-20-5165.
Do not use LHS (Large Hole System) Components with rotary hammers
5340-20 and 5342-20. The bits could fail, breaking apart at the threaded
stud and causing injury and property damage.
five year Tool limiTed WarranTy
Every MILWAUKEE tool is tested before leaving the factory and is war-
ranted to be free from defects in material and workmanship. MILWAUKEE
will repair or replace (at MILWAUKEE's discretion), without charge, any
tool (including battery chargers) which examination proves to be defective
in material or workmanship from five (5) years after the date of purchase.
Return the tool and a copy of the purchase receipt or other proof of pur-
chase to a MILWAUKEE Factory Service/Sales Support Branch location or
MILWAUKEE Authorized Service Station, freight prepaid and insured. This
warranty does not cover damage from repairs made or attempted by other
than MILWAUKEE authorized personnel, abuse, normal wear and tear, lack
of maintenance, or accidents.
Battery Packs, Flashlights, and Radios are warranted for one (1) year from
the date of purchase.
THE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN ARE
EXCLUSIVE. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY
INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, INCLUDING
LOSS OF PROFITS.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WAR-
RANTIES, OR CONDITIONS, WRITTEN OR ORAL, EXPRESSED OR
IMPLIED FOR MERCHANTABLILITY OR FITNESS FOR PARTICULAR
USE OR PURPOSE.
This warranty gives you specific legal rights. You may also have other rights
that vary from state to state and province to province. In those states that
do not allow the exclusion of implied warranties or limitation of incidental
or consequential damages, the above limitations or exclusions may not
apply to you. This warranty applies to the United States, Canada, and
Warning
Cat.No.
48-20-5125
48-20-5130
48-20-5135
48-20-5140
48-20-5145
48-20-5150
48-20-5155
48-20-5160
48-20-5165
page 11