Plunge Cuts; Sawing According To Tracings; Sawing With The Parallel Stop; Scoring With The Guide Rail (Special Accessories) - Mafell MT55 18M bl Traducción Del Manual De Instrucciones Original

Sierra de incisión
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 70
In addition, the machine can be tilted to -1° or 48°.
To tilt to -1°, pull the slide bar 14 (Fig. 4)
backwards in the direction of the arrow and hold
on to it.
Tilt the machine to -1°.
To tilt the machine to 48°, press the limit stop 15
(Fig. 3) downwards.
Tilt the machine to 48°.
45° and 0°- limit stop are automatically reset
after they have been traversed.

5.5 Plunge cuts

Danger
Risk of backlash during plunge
cuts! Prior to plunging, place the
machine with the rear edge of its
base plate against a limit stop
fastened on the workpiece. When
using the guide rail (special
accessories) you must fasten the
limit stop available as special
accessory on the guide rail. Keep
a firm hold on the machine handle
during plunging and push the saw
lightly forward!
The markings 16 (Fig. 1) on the bottom saw
guard and on the slide bar serve as orientation
for the cutting area of the completely plunged
saw blade if the guide rail (special accessories)
is used.

5.6 Sawing according to tracings

The figure is equipped with a tracked score indicator
17 (Fig. 1) both for straight cuts and for bevel cuts.
This tracing edge corresponds to the saw blade's
inside.
Secure the workpiece against shifting and
arrange the workpiece supports such that the
saw blade is running freely underneath the
workpiece.
Hold the machine by its handle and place the
front part of its base plate onto the workpiece.
Switch on the plunge cut saw (see Chapter 5.2).
Plunge to the set cutting depth and slide the
machine evenly forward in the direction of the
cut.
When the cut is completed, switch off the saw
by releasing the gearshift lever 8 (Fig. 4). Tilt the
saw unit back into the top locked position.

5.7 Sawing with the parallel stop

When making parallel cuts, the parallel guide fence
18 (Fig. 1) serves to saw parallel to an already
existing edge. The guide fence can be attached to the
left or right of the machine. The cutting range on the
right-hand side amounts to approx. 140 mm (5 ½ in.)
and on the left-hand side to approx. 295 mm (11 5/8
in.).
Once you have unfastened the wing screws you
can adjust the cutting width 19 (Fig. 2) by
moving the guide fence accordingly and
afterwards retightening the wing screws.
In addition, by simply turning it around (guide face for
the workpiece edge points upwards), the parallel stop
can also be used as double support to improve
guidance of the plunge cut saw. Now the machine
can be guided along a lath that is fastened on the
workpiece.
5.8 Scoring
with
accessories)
In case of panel materials you can
achieve a clean cut if you score.
Use a suitable saw blade (see
Chapter 4.5).
To avoid the surface from tearing out, proceed as
follows:
Fasten the guide rail on the workpiece.
Tilt the locking lever 20 (Fig. 2) clockwise up to
the limit stop. The scoring depth is now set to
approx. 3 mm (1/8 in.).
Place the machine with the guide groove onto
the guide rail.
Set the cutting depth - take into account the
guide rail thickness (see Chapter 5.3).
Score the board. Tilt the locking lever 20 (Fig. 2)
counter clockwise up to the limit stop.
Plunge to the preset cutting depth and saw the
full board thickness.
-26-
the
guide
rail
(special

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

918801918802918821918825

Tabla de contenido