Preparing For Startup; Start-Up; Electric Supply - Altrad Lescha TSL Serie Manual De Instrucciones Original

The connector of the connection cable must be splash-proof.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do not
use the cable to pull the plug from the socket.
Check regularly the cable of the table saw and get possible
damages repaired by a professional specialist.
When running the connection line observe that it does not
interfere, is not squeezed, bent and the plug connection does
not get wet.
Regularly check the extension cables and replace them if they
are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables especially
approved and appropriately labelled for outdoor use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
The electrical connection or repairs to electrical parts of the
machine must be carried out by a certified electrician or one
of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out by
the manufacturer or one of his customer service points.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer is
not liable for any damage or injury resulting from such
action.

Preparing for startup

To achieve flawless functioning of the machine, please follow
the instructions listed:
• Place the machine at a location that meets the following
conditions:
− secured against slipping
− free of vibrations
− even
− free of tripping hazards
− adequate light
• Before each use, check
− Defective connecting lines (cracks, cuts, etc.).
Never use defective lines!
− the saw blade for flawless condition
• Do not use any cracked saw blades or such that have
changed their shape.
• Do not use saw blades made of high-speed steel.
• Always stand to the side of the danger zone (saw blade) when
working at the bench.

Start-up

Checking the safety devices
(before each starting)
− Proper working condition of the safety guard.
− Check the switch by turning it on and off.
− Do not use any device where the switch cannot be switched
on and off. Damaged switches must be repaired or replaced
immediately by the customer service.
− Brake
− The saw blade must stand still within 10 seconds after it was
switched off. The brake is defective if this time is exceeded.
The saw must then be repaired by the manufacturer or a
workshop appointed by the manufacturer.
− The push stick must be within easy reach.
⇒ Replace defective push sticks by new ones.
− Correct splitting wedge setting (see also Fig. 11).
Rotating direction of the saw blade
Ensure that the rotational direction of the saw blade is the
same as the rotational direction given on the guard (33).
The rotating direction of three-phase
motors can be changed by inserting a
screwdriver in the connector collar
provided for this purpose and turning
left or right while exerting a light
pressure to adjust the correct rotating
direction.
Selection of saw blades
⇒ Observe the splitting wedge thickness "S"; it is etched
into the side of the splitting wedge.
The splitting wedge must not be thinner than the saw
blade, and not thicker than the kerf width produced by the
blade.
The rating plate specifies maximum and minimum saw
blade diameters, as well as the hole diameter.
Do not use saw blades that are designed for a lower max.
speed (see identification on the saw blade) than the motor
speed (see the technical data).

Electric supply

Compare the voltage listed on the machine's type plate, e.g.
230 V, with the mains voltage and connect the machine to a
suited and properly earthed electrical socket.
• Alternating-current motor:
Schuko (earthed) socket, mains voltage 230 V, with earth-
leakage circuit breaker (FI switch 30 mA).
• Three-phase motor:
CEE socket, 3-pin+N+PE, mains voltage 380 V or 400 V, with
earth-leakage circuit breaker (FI switch 30 mA).
Use an extension cable in compliance with IEC 60245 (H 07 RN-
F) having a core cross-section of at least:
⇒ 1.5 mm² for a cable length of up to 25 m.
⇒ 2.5 mm² for a cable length exceeding 25 m.
Main fuse
EU 16 A
UK 13 A
14