Westin 65-62057 Manual De Instrucciones

#65-62057
T-Connector
Wiring Kit
INSTALLATION INSTRUCTIONS
Fits: 2011 - 2014 Ford Edge
Kit Includes:
(1) Wiring Harness (1) Ring Terminal
with 4-Flat Connector (1) Butt Terminal
(8) 6" Cable Ties (1) Fuse Holder
(1) 15" Cable Ties (1) 10 Amp Fuse
(1) Primary Lead Wire (1) #10 Self Tapping Screw
T-Connector Wiring Kit
INSTALLATION INSTRUCTIONS
1. Read instructions thoroughly before beginning.
2. Open rear hatch. Remove driver and passenger side
taillights by removing two 8mm bolts that hold each one
inplace shown in Figure 1. Identify vehicle's taillight connectors.
They will be similar to those on the T-Connector. Separate
vehicle' s connectors taking care not to damage the locking tabs.
Inspect connectors for dirt and debris and clean if necessary.
3. Unseat rubber grommet on both sides shown in Figure 2.
Using an utility knife make a small slit in grommet from center
to outside, away from the factory wire harness, taking care not to
damage any wires.
4. Inside the vehicle remove all floor mats and spare tire cover
and set aside. Remove rear threshold and side cargo trays on
bth sides of spare tire shown in Figure 3. On driver side remove
cargo tie down shown in Figure 4 and gently pull side panel away
from vehicle body taking care not to break any alignment tabs or
damage panel.
5. On drivers side route T-Connector ends with the Yellow wire
wire behind the side panel and through opening where grommet
was removed in Step 3. Position connectors between separated
vehicle harness connectors shown in Figure 5 and press connectors
firmly into vehicle connectors until they lock into place. Pull on
connectors to ensure locks are engaged.
6. There are two ways to mount the ground ring on the White
wire:
6a: Locate a clean accessible mounting location on the vehicle
near wiring harness ends within reach of ground ring on white wire.
Remove any debris or undercoating to expose a clean metal surface
and drill a 3/32" hole.
Caution: Take care not to drill through the body or any exposed
surface.
Secure ring on white wire using ground screw provided.
6a: Using an 8mm socket remove the factory ground bolt shown
in Figure 6. Place ground ring on T-Connector with factory ground
ring and re-attach factory ground bolt.
7. Route T-Connector ends containing Green wire and 4-Flat
down through opening behind driver' s side side panel. Route across
rear of vehicle under location of removed threshold to passenger
side. Repeat Step 5 for connector plugging.
8. Disconnect the vehicle's Negative(-) battery cable.
9. Route the 12 gauge black wire from the battery
compartment under the vehicle along the frame shown in
75-62057 REV A 032613
Figure 7. Secure wire to vehicle using cable ties provided.
10. Cut the Yellow inline fuseholder and strip 5/16" of the
insulation from one end attach the 3/8" ring terminal using a
crimping tool.
11. On the other end of the fuseholder strip 5/16" of the
insulation and crimp the yellow butt connector provided and
attach it to the 12 gauge black wire.
12. With the fuse removed, attach the 3/8" ring terminal to
the vehicles positive (+) battery terminal shown in Figure 8.
Warning: Do not attempt to connect the black power wire
to the vehicle fuse panel or any other accessory wiring.
Failure to connect directly to the vehicle battery could
cuase vehicle damage and/or trailer lighting failure.
13. At rear of the vehicle, strip 5/16" of insulation from the
black 12 gauge wire and connect it to the butt connector on
the red wire on the taillight converter.
14. Reattach the vehicle Negative (-) battery wire.
15. Place the 10 Amp fuse into the fuse holder installed in
Step 10.
16. Confirm correct operation with a test light or by using a
trailer.
17. Secure the T-Connector black converter box using the
double-sided tape and/or the 15" cable tie provided. Secure
the remainder of the T-Connectors wires with remaining cable
ties provided to prevent damage or rattling.
18. Re-install all previously removed parts from the
preceeding steps.
Westin Automotive Products, Inc. ● 320 W. Covina Boulevard, San Dimas, CA 91773 ● Got Questions? Call: (888) 872-6281
Fig. 1 Fig. 2
Fig. 4
Fig. 6
Fig. 5
INSTRUCCIONES DE INSTALACIÓN
Español:
1. Lea las instrucciones a fondo antes de comenzar.
2. Abrir puerta trasera. Retire la unidad y del lado del
pasajero luces traseras mediante la eliminación de dos
tornillos de 8 mm que contienen cada uno en lugar que se
muestra en la Figura 1. Identificar los conectore s de la luz
trasera del vehículo. Serán similares a los de la T-Connector.
Separado conectores del vehículo teniendo cuidado de no
dañar el bloqueo fichas. Inspeccione los conectores de la
suciedad y los escombros y limpiar si necesario.
3. Desbancar arandela de goma en ambos lados se
muestra en la Figura 2. El uso de un cuchillo hacer una
pequeña incisión en ojal del centro al aire libre, lejos del
mazo de cables de fábrica, teniendo cuidado de no
dañar los cables.
4. En el interior del vehículo eliminar todas las alfombras
de piso y rueda de repuesto cubierta. Quitar Umbral
traseros y latera les bandejas de carga en ambos lados de la
rue da de repuesto se muestra en la Figura 3. En el lado del
conductor quite empate de carga abajo se muestra en la
Figura 4 y tire suavemente de panel lateral de carrocería
del vehículo teniendo cuidado de no romper ninguna
lengüetas de alineación o daños panel.
Fig. 3
Fig. 7
Fig. 8
Page 1 of 2