General Characteristics - Cristher PAR56 OnLED Manual De Instrucciones

ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions before
beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the OnLED PAR 56, follow the instructions provided below:
1. VERIFY THE CONTENTS OF THE PACKING:
The following accessories are included inside the box:
• Unit projector
• Manual for electrical connection

2. GENERAL CHARACTERISTICS:

This projector has been designed to be used totally submerged in water. It is a Class III electric apparatus with very low
safety voltage (12V with alternating current).
The projector compiles with IPX8 degree of protection (resistance to penetration of dust, solid bodies and humidity) at a
nominal immersion depth of 2 m.
This projector compiles with international safety standards for lights, especially the EN 60598-2-18 standard. LIGHTS
PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric components
which have been inserted or handled at locations other than its own premises.
3. INSTALLATION:
• The projector must only work submerged and fixed to the vertical walls of the swimming pool. Never turning the projector
on if it is not submerged in water. In the OnLED v2 models it is essential that the direction of the lamp is adequate,
situating "TOP" on the top part of the projector.
• To correctly light a swimming pool we recommend you:
Install a lamp in the range OnLED v1 every 20 m² of water surface.
Install a lamp in the range OnLED v2 every 25 m² of water surface.
Note: Recommendation valid for light coloured pools. In darker coloured pools or stainless steel pools we recommend
oversizing the proportion of projectors per m².
• In order to prevent glare, the projector s should be installed so that they face away from the residence or usual view of
the swimming pool.
• In the event that lighting is used in training or competition pools, the projector s should be installed on the sides to
prevent glare on the swimmers.
• To avoid the need to empty the pool to change the lamp, we recommend that the projector be installed in areas which
are accessible from the upper edge of the pool, at approximately 400-700 mm from the water surface (Fig. 1).
Prior to installation verify that the gland seal (P-Fig.4) has been fully tightened.
• The method of fastening the housing to the pool wall varies depending on whether it is a projector for concrete pools,
prefabricated or panel swimming pool. Read the instructions for assembling the niche.
• In installations where you want to replace a conventional spotlight by a LED projector, using the existing wiring, it is
strongly recommended to use underwater resin splicing. It is not recommended to use silicone to try to seal the connec-
tion point of the wires.
4. ASSEMBLY:
After installation of the housing and the clamp, assemble the projector .
To connect the projector to the electric power supply insert the cable through the gland seal nut of the niche. Tighten the
gland seal nut until you can verify that the cable will not yield when you pull on it with your hand.
Take the precaution of leaving 1.5 m of cable wound on the base of the projector in order to be able to remove the projector
to the edge of the pool in the event that lamp replacement or handling is required (Fig 1).
Assembly STD projector
Insert the entire projector assembly in the housing. In order to obtain good pool lighting it is important that the anagram
of the decorative ring is located on the upper part (Fig 2).
Screw in the screws of the trim until the fixing staple is anchored to the insides of the niche.(Fig 3).
Assembly Global projector
The Global anchoring system can be adapted to Ø220 to 235 mm niches (Fig 4).
Insert the entire projector assembly in the housing (Fig. 6). In order to obtain good pool lighting it is important that the
anagram of the decorative ring is located on the upper part (Fig. 2).
Screw in the screws of the trim until the fixing staple is anchored to the insides of the niche. (Fig.3).
• Installation and maintenance manual
• Bag with 2 connection screws
2
• Guarantee booklet