Select Blower Option And Install Ductwork; Prepare The Installation - Broan best PIK33 Instrucciones De Instalación

1. SELECT BLOWER OPTION AND INSTALL DUCTWORK

Either an interior or exterior blower or in-line blower may be used with this insert. The insert model PIK33 or PIK45 must be
installed with blower models P5, P8, ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 or EB15 only. Other blowers cannot be substituted.
(Blowers sold separately).
Plan where and how the ductwork will be installed. Access to the top of the hood is preferred for connection of ductwork. As an
alternative, flexible metal ductwork may be used.
If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 8, 13, 14, 16, 17, 19
and up of this manual.
Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Use round ductwork, with a
short section (about 4' expanded) of flexible metal duct (optional) for attachment to the transition. Use screws to attach flexible
metal duct to the rigid duct. Use 2" duct tape to seal duct joints.
The minimum hood distance above cooktop must not be less than 24". A maximum of 30" above cooktop is highly
recommended for best capture of cooking impurities.
Distances over 30" are at the installer and users discretion.
Roof cap
7" or 8" round ducts
with 7" or 8" round
metal flex. duct (optional)
3 1/4" x 10" to 7" or 8" transition
or 3 1/4" x 14" to 8" transition
Insert with
Wall
interior blower
cap
24" minimum
above cooking surface
HH0038A
MODEL P5 (SINGLE) OR
P8 (DOUBLE) INTERIOR BLOWER
TYPICAL DUCTWORK

2. PREPARE THE INSTALLATION

When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.
Make sure that the following items are included:
- Insert
- Accessories: • Baffle filters (3 for PIK33 model, 4 for PIK45 model)
• Bag of parts including: (4) lock nuts, (1) wire clamp, (8) n°. 8 x 3/4" standard screws,
Parts sold separately:
- Interior blower Model P5 includes blower, rough-in kit, flow deviator and 3¼" x 10" adapter
- Interior blower Model P8 includes blower, rough-in kit, flow deviator and 3¼" x 10" adapter and 3¼" x 14" adapter
- In-line blower assembly ILB3, ILB6, ILB9 or ILB11 (all include rough-in plate and transition)
- Exterior blower assembly EB6, EB9, EB12 or EB15 (all include rough-in plate)
- Shielded halogen lamps (120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base)
- Custom hood liner Model L3336S, L3342S, L4548S, L4554S or L4560S (optional)
- Ambient light panel Model ALP36, ALP42, ALP48, ALP54 or ALP60 (optional)
- Backsplash RMP Series (optional)
- WCPI Remote control (optional)
- Transitions, ducts (rigid and flexible), elbows, dampers, wall and roof caps. Refer to page 3 and 4 for a complete list of
venting options and model numbers.
NOTE: During installation, protect countertop and/or cooktop.
Exterior blower
10" round duct
10" round metal
flex. duct
(optional)
Insert with
exterior blower
24" minimum
above
cooking surface
HH0039A
MODEL EB6, EB9, EB12 OR
EB15 EXTERIOR BLOWER
TYPICAL DUCTWORK
CAUTION
(2) wire connectors, (2) n°. 6 x 1/2" standard screws, (8) n°. 8 x 3/8" screws.
Discard items not used.
- 5 -
10" round duct
In-line blower
10" round metal
flex. duct
(optional)
24" minimum
above
cooking surface
HH0058A
MODEL ILB3, ILB6, ILB9 OR ILB11
IN-LINE BLOWER
TYPICAL DUCTWORK
Roof cap
Wall
cap
Insert