Jøtul F 370 Serie Manual De Instalación Con Información Técnica página 30

UNITED KINGDOM
3.5 Control of functions (fig. 26)
When the product is set up, always check the control functions.
These shall move easily and function satisfactorily.
Jøtul F 370 is equipped with the following controls:
Air vent fig. 26A
Left position: Closed
Right position: Open
Ignition vent, fig. 26B)
Pushed in: Closed
Pulled out: Open
Riddling grate (same handle as for the ignition vent) (Fig. 26B)
Right handle is pushed in and out.
Handle for door fig. 26C:
Is opened by pulling handle out.
3.6 Ash removal
Jøtul F 370 has an ash pan which makes it easy to remove the ashes.
1. Only remove ashes when the fireplace is cold.
2. Push/pull the handle for the ash grate/ignition vent out and in
several times so that the ashes fall down into the ash pan. Use
something like a glove to grab the handle on the ash pan.
3. Make sure that the ash pan doesn't fill up so high that it keeps
ash from coming through the grate into the pan.
4. Make sure the door to the ash pan is securely shut when the
stove is in use.
For the rest, see description of how to handle ash in the Manual
on general use and maintenance in Point «6.1 Fire preventive
measures».
3.7 Use (fig. 26)
• Open the air vent and the ignition vent by pulling it out all
the way (fig. 26). If necessary, keep the door slightly open.
(Use a glove, for example, as the handle can become hot.)
• Place two medium sized logs in/out on each side of the base.
N.B. In order to avoid sooting on the glass, it is important that
the log is not placed adjacent to the glass on the product.
• Crumple some newspaper (or birch bark) between these and
add some kindling wood in a criss-cross pattern on top and
light the newspaper.
• Gradually increase the size of the fire, but the wood should
not be stacked higher than the horizontal holes on the back
burn plate. See fig. 26H.
• Close the ignition vent
ignited and the fire is burning well.
• Check that the afterburning (secondary combustion) starts. This
is best indicated by yellow, flickering flames under the baffle.
• Then regulate the rate of combustion to the desired level of
heating by adjusting the air vent (fig. 26A).
See the general manual for information regarding use of the
stove.
30
(fig. 26 B) when the firewood has
4.0 Service
Warning! Any unauthorised change to the product is illegal.
Only use original spare parts.
4.1 Replacing the baffle/exhaust
deflector (fig. 23 and 26)
(N.B. If you use tools, be aware that the vermiculite plates may
be damaged by rough treatment).
1. Lift up the front edge of the baffle plate and tilt it out
Remove the side burn plates (fig. 26F) and the rear burn plate
(fig. 26 E).
2. The exhaust deflector, in cast-iron - that is located above the
baffle plate, rests with the bar on the ribs at the rear flue
outlet (fig. 23A). Lift the exhaust deflector slightly up, pull it
forward and tilt it out.
3. For reassembly follow the same procedure for installation,
but in reverse.
4.2 Replacement of burn plates/base
plate (fig. 24 and 26)
(N.B. If you use tools, be aware that the vermiculite plates may
be damaged by rough treatment).
1. Lift up the front edge of the baffle plate and tilt it out.
Remove the side burn plates (fig. 26F) and the rear burn plate
(fig. 23 E).
2. Then lift up the grate and the base plate and take it out
26 D).
3. Follow the same procedure for installation, but in the opposite
sequence.
4. When reassembling the grate and the base plate, make sure
that the riddling bar (fig. 24 A) that moves the riddling grate
is threaded into the slot on the right edge of the grate.
4.3 Replacing the inner/outer side
glass (fig. 23, 26, 27 and 27)
1. Lift up the front edge of the baffle plate and tilt it out Remove
the side burn plates (fig. 26F) and the rear burn plate (fig. 26E).
2. The exhaust deflector, in cast-iron - that is located above the
baffle plate, rests with the bar on the ribs at the rear flue
outlet (fig. 23 A). Lift the exhaust deflector slightly up, pull it
forward and tilt it out.
3. Remove riddling grate, base plate and ash pan
4. Unscrew the upper and lower screws
tilt the glass holder with the glass carefully out through
the door. N.B. The glass holder also keeps the outer glass
in place
5. Remove the glass and possibly replace gaskets. If needed
replace the external glass.
6. For reassembly follow the same procedure for installation,
but in reverse.
(fig. 26G).
(fig.
(fig. 26 D).
(fig. 27 A and 28 A), and