3M D8000 Serie Instrucciones De Uso página 89

R = Re-usable
NR = Non re-usable (single shift use only)
ce End of Shelf Life. Date format - mm/yyyy
]
End of shelf life (use-by) date is marked on the product and
packaging.
For Single Use Only
)
Maximum Use Time 50 hours
(
Name and address of Manufacturer
ral
:
Dispose in accordance with local regulations
J
Packaging not suitable for food contact.
K
TECHNICAL SPECIFICATION
3M gas/vapour filters generally protect against either single or
hould
multiple contaminant type(s) and against particulates when
hey
combined with a particulate filter. 3M combination filters generally
our protect against either single or multiple gas/vapour type(s) and
at the against particulates.
ch
Filter Type
lastic
A
e
B
he blue
aching
o
t up
E
. 3).
ease
K
4).
ase
Formaldehyde
s is
AX
y of the
tration
umidity
Hg
P
dry,
Gas/Vapour Filter Classes
ng is
Gas Filter Class
e
1
2
ptable
Particulate filters can also be classified into one of three classes
depending on the efficiency in removing contaminants from the
s 5
inhaled air.
Colour Code Type of Contaminant
Brown Organic vapours with boiling
point >65°C (with good
warning properties) as
specified by the manufacturer
Inorganic Gases & Vapours
Grey
(with good warning
properties) as specified by the
manufacturer
Yellow Acid Gases (with good
warning properties) as
specified by the manufacturer
Green Ammonia and Organic
Ammonia derivatives (with
good warning properties) as
specified by the manufacturer
Olive green Formaldehyde vapour
Organic vapours with boiling
Brown
point equal or less than 65°C
(with good warning
properties) as specified by the
manufacturer
Mercury vapour
Red
Solid and non-volatile liquid
White
aerosols
NPF 3M™ Half mask*
10 (or 1000 ppm (0.1% vol)
whichever is lower)
10 (or 1000 ppm (0.5% vol)
whichever is lower)
Particulate Filter NPF 3M™ Half mask*
Class
P1 10 <Local P1 APF Half Mask>
P2 10 <Local P2 APF Half Mask>
P3 10 <Local P3 APF Half Mask>
Required Minimum Protection Factor (RMPF) - the protection factor
required to reduce exposure to an acceptable level. It is expressed
as a ratio of the measured ambient airborne concentration of a
contamniant to an acceptable exposure level or stanard. Many
countries applyAssigned Protection Factors (APFs). For P3 rated
filters: Provides P3 protection only with a full facepiece respirator.
Provides P2 protection with half facepiece respirator. Employers
may apply a value lower than theAPF if deemed applicable. Please
refer to EN 529:2005 orAS/NZS1715 workplace protection
guidance for application of these numbers in the workplace. Please
contact 3M for further information.
3M™ D8000 Series Filters
Filter Type Classification Type of Contaminant
3M D8051
A1
3M D8055 A2
3M D8059 ABEK1
3M D8094 ABEK1P3 R
3M D8095 A2P3 R
APPROVALS
These products are type approved and audited annually by either:
BSI Group, The Netherlands B.V. Say Building, John M.
Keynesplein 9, 1066 EPAmsterdam, The Netherlands, Notified
Body No. 2797 and / or BSIAssurance UK Ltd, Kitemark Court,
DavyAvenue, Knowlhill, Milton Keynes MK5 8PP, UK, Notified Body
No. 0086. These products meet the requirements of European
Regulation (EU) 2016/425 and applicable local legislation. The
applicable European/local legislation and Notified Body can be
determined by reviewing the Certificate(s) and Declaration(s) of
Conformity at www.3m.com/Respiratory/certs.
88
Organic vapours with boiling
point >65°C (with good
warning properties) as
specified by the manufacturer
Organic vapours with boiling
point >65°C (with good
warning properties) as
specified by the manufacturer
Combination organic vapours
(b.pt > 65C (with good
warning properties) as
specified by the
manufacturer), inorganic &
acid gases & ammonia
Combination organic vapours
(b.pt > 65C (with good
warning properties) as
specified by the
manufacturer), inorganic &
acid gases, ammonia &
particulates
Organic vapours with boiling
point >65°C (with good
warning properties) as
specified by the manufacturer
and particulates