Publicidad
Idiomas disponibles
Idiomas disponibles
ignitor
Lighting
(continued)
8. Once each burner has ignited,
turn knobs to desired setting.
9. If ignitor
does not work, follow
match lighting
instructions.
Turn controls
and
gas source or tank
OFF when
not
in
USe.
CAUTioN
Burner Flame Check
" Remove cooking
grates and Heat Diffusers.
Light burners, rotate
knobs from Hi to LOW. You should see a smaller flame
in
LOW position
than seen on Hi. Perform
burner flame
check
on sideburner,
also. Always
check flame
prior to each use. If
only low flame
is seen refer to "Sudden
drop or low flame"
in
the Troubleshooting
Section.
If ignition does NOT occur in 5 seconds, turn the burner
controls OFF, wait 5 minutes and repeat the lighting
)rocedure. if the burner does not ignite with the valve
open, gas will continue to flow out of the burner and
could accidentally
ignite with risk of injury.
Match-Lighting
Do not lean over grill while lighting.
1. Open lid. Turn ON gas at LP cylinder.
2. Place match into match holder (hanging
from side panel of
grill). Light match; then light burner by placing
match through
the match light hole on right or left side of grill.
3. Push in and turn far right or far left burner knob to the HI
position,
depending
on match light hole selected.
Be sure
burner lights and stays lit.
4. Light adjacent
burners in sequence by pushing knobs in and
turning to the Hi position.
Sideburner
ignitor
Lighting
Do not lean over grill while lighting.
i. Open sldeburner
lid. Turn ON gas at LP cylinder.
2. Turn sideburner
knob to the HI position,
push and hold
ELECTRONIC
IGNITION
button.
3. If sideburner
does NOT light within 5 seconds, turn knob to
OFF, wait 5 minutes, then
repeat lighting
procedure.
Sideburner
Match
Lighting
1. Open sldeburner
lid. Turn ON
gas at LP cylinder.
2. Remove steamer tray and basket.
3. Place lit match near burner.
4. Turn sideburner
knob to the
Hi position.
Be sure burner lights and stays lit.
5. Replace steamer tray and basket.
12 • 464323113
Turning
Grill Off
- Turn all knobs to the OFF position. Turn LP cylinder
OFF by
turning
hand-wheel
clockwise
to a full stop.
Ignitor
Check
" Turn gas off at LP cylinder.
Press and hold electronic
ignitor
button.
A "Clicking"
should be heard and spark seen each
time between
each collector
box or burner and electrode.
See "Troubleshooting"
if no click or spark.
Valve Check
* Important:
Make sure gas is off at LP cyffnder
before
checking
valves.
Knobs loci< in OFF position.
To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before
using grill. Turn knobs to LOW position
then turn back to
OFF position. Valves should turn smoothly.
Hose Check
- Before each use, check to see if hoses are cut or worn.
Replace damaged
hoses before
using grill. Use only
identical
replacement
part valve/hose/regulator
as
specified
in the Parts List of this Use and Care Guide.
General
Grill Cleaning
- Do not mistake
brown or black accumulation
of grease and
smoke for paint.
Interiors of gas grills are not painted
at the
factory
(and should never be painted).
Apply
a strong solution
of detergent
and water
or use a grill cleaner
with scrub brush
on insides of grill lid and bottom.
Rinse and allow to completely
air dry. Do not apply a caustic grffl/oven
cleaner
to painted
surfaces.
" Plastic parts: Wash with warm
soapy water
and wipe dry.
Do not use citrisol, abrasive
cleaners,
degreasers
or a
concentrated
grill cleaner
on plastic parts. Damage
to and
failure
of parts can result.
" Porcelaln
surfaces:
Because of glass-like
composition,
most
residue can be wiped
away with baking
soda/water
solution
or
specially
formulated
cleaner.
Use nonabrasive
scouring
powder
for stubborn
stains.
" Painted
surfaces:
Wash with mild detergent
or nonabrasive
cleaner
and warm soapy water. Wipe
dry with a soft
nonabrasive
cloth.
" Stainless
steel surfaces:
To maintain
your grill's high quality
appearance,
wash with mild detergent
and warm
soapy water
and wipe dry with a soft cloth after each use. Baked-on
grease
deposits
may require the use of an abrasive
plastic cleaning
pad. Use only in direction
of brushed finish to avoid damage.
Do not use abrasive
pad on areas with graphics.
" Cooking surfaces:
If a bristle brush is used to clean any of
the grill cooking
surfaces, ensure no loose bristles remain
on
cooking
surfaces prior to grilling.
It is not recommended
to
clean cooking
surfaces
while grill is hot.
Publicidad
