Safety Instructions; Inspection And Maintenance - KBT 360 Modo De Empleo

INSTRUCTIONS FOR USE

SAFETY INSTRUCTIONS

1. Please keep this instruction sheet safely for future reference.
2. Please do not modify the product or the assembly details in any way. Modifi cations will affect the structural in-
tegrity and replacement parts will be at the buyer's expense. Inappropriate use or faulty application of the
product are explicitly forbidden and absolve the manufacturer of all liability. This product needs to be mounted
by an adult before use.
3. The use of the item is allowed only under continuous supervision by an adult. The product is suitable for indi-
viduals weighing up to 100 kg. The product is not suitable for children under 36 months, due to a lack of extra
safety precautions and taking into account the limited mental capacities of toddlers. Risk of falling!
4. This product meets all security aspects of the European standards EN1176-1,11:2008. This product is fi t for
outdoor commercial playgrounds.
5. Equipment shall be constructed so that any openings with a lower edge more than 600 mm above the ground
do not create head and neck entrapment hazards. Completely bound openings shall be not less than 230 mm in
diameter unless the opening is smaller than 130 mm in diameter and smaller than 157x89 mm.
6. Equipment shall be constructed so that any openings do not create fi nger entrapment. Openings shall not be
less than 25 mm in diameter unless the opening is smaller than 8 mm in diameter.
7. When mounting or assembling the armed rope construction, attention should be given to the minimum required
distance between the armed rope construction and eventual obstacles (impact area). Dimension of the impact
area depends on the free height of fall (FIG I). The impact area shall be at least 1,5 m around the equipment,
measured horizontally and shall increase for free height of fall above 1,5 m. In this safety area no hard, angular
or pointed objects should be present (FIG II).
8. The safety surface underneath the product must be flat, and be covered in a suitable way (eg. rubber tiles, bark,
wood chips) and meet the requirements of EN 1176-1:2008. The indicator of the surface level should be the
base level mark found on the supporting structure of the whole device (e.g. on the pole). The product must not
be placed on asphalt, concrete or any other hard surface. There cannot be an overlapping of surrounding free
spaces or safety areas.
9. Connections shall be safeguarded so that they cannot be undone without tools (e.g. with glued threaded joints).
10. No spare parts are provided with the device. In case of a damage, spare parts can be purchased from the man-
ufacturer.
11. The minimum installation space should be within 2 m from the device to be installed.
12. During installation you should make sure that: the pole is placed vertically, all the screws and fastenings are
tightened, the place of installation is secured and marked. Before the device can be used, the stability of all the
elements should be checked, protection tapes removed and the level and condition of the shockabsorbing
surface checked.
13. Should the device be found to be incomplete or damaged, the construction must be immediately protected and
its use prevented by using a signalizing white and red tape and placing information that the device is damaged.
Until the damage is repaired, the device should be excluded from use by the playground users.

INSPECTION AND MAINTENANCE

The frequency of inspection and maintenance will vary with the type of equipment or materials used or other factors
(e.g. heavy use, levels of vandalism, coastal location, air pollution, age of equipment, ...). The frequency of the
inspection checks should be increased according to the occurrence of special factors.
Routine visual inspection (weekly to monthly)
- Always check that the bolts and nuts are securely fastened.
- Check the shock absorbing surface for objects that don't belong there.
- Check for missing parts.
- Check the equipment ground clearances.
Operational inspection (1 to 3 months)
- Check the stability of the construction.
- Check every part for excessive wear and replace when necessary.
Annual inspection (1 to 2 times per year)
- Check for rust and corrosion.
- Check every part for excessive wear and replace when necessary.
2
armed rope pyramid net
EN
4
6
a
ASSEMBLY - MONTAGE - MONTAJE - MONTAGGIO - MONTAŻ
ASSEMBLY - MONTAGE - MONTAJE
MONTAGGIO - MONTAŻ
5
b
Instructions for use - M360.04 - armed rope pyramid net
c
15