Publicidad
Safety Instructions (continued)
10. Keep fingers away from a running
compressor; fast moving and hot
parts will cause injury and/or burns.
11. If the equipment should start to
vibrate abnormally, STOP the
engine/motor and check immediately
for the cause. Vibration is generally a
warning of trouble.
WARNING:
!
NEVER refuel a run-
ning or hot engine.
Explosive fuel can cause fires
and severe burns. Avoid over-
filling fuel tank.
12. Check fuel level before starting the
engine. Do not fill the gas tank
indoors. Wipe off any spilled gas
before starting the engine.
DANGER:
!
Gasoline vapor is highly flam-
mable. Refill outdoors or only in
well ventilated areas. Do not
store, spill or use gasoline near
an open flame or heat devices
such as a stove, furnace, or
water heater, which utilize a
pilot light, or any device that
can create a spark. If gasoline
is accidentally spilled, move
unit away from the spill area
and avoid creating any source
of ignition until gasoline vapors
have dissipated.
WARNING:
!
Motors, electrical
equipment and con-
trols can cause electrical arcs
that will ignite a flammable gas
or vapor. Never operate or
repair in or near a flammable
gas or vapor. Never store flam-
mable liquids or gases in the
vicinity of the compressor.
WARNING:
!
Carbon monoxide can
cause severe nausea,
fainting or death. Do
not operate unit
inside a closed building or a
poorly ventilated area.
13. To reduce fire hazard, keep
engine/motor exterior free of oil, sol-
vent, or excessive grease.
WARNING:
!
Never remove or attempt to
adjust safety valve. Keep safety
valve free from paint and other
accumulations.
14. Do not tamper with governor setting
on engine. Overspeeding the unit
severely shortens engine life and may
also be very hazardous.
DANGER:
!
Never attempt to
repair or modify a
tank! Welding, drilling
or any other modification will
weaken the tank resulting in
damage from rupture or explo-
sion. Always replace worn or
damaged tanks.
15. Tanks rust from moisture build-up,
which weakens the tank. Make sure to
drain tank daily and inspect periodical-
ly for unsafe conditions such as rust
formation and corrosion.
4
Pièces de rechange
Pour les pièces de rechange, appeler le 1-800-4-RIDGID
S'il vous plaît fournir l'information suivant:
-Numéro du modèle
-Numéro de série (si applicable)
-Description de la pièce et son numéro sur la liste de pièces
No.
No de
Numéro
Ref.
catalogue
de pièce
1
17993
BG220901AJ
2
17998
ST026200AV
3
18003
BT023100AV
4
18008
ST073915AV
5
18013
ST073916AV
6
18018
ST070827AV
7
18023
WL021402AV
8
17868
ST119704AV
9
17798
V-215106AV
10
17783
ST071626AV
11
18028
ST160002AV
12
17913
D-1403
13
17918
ST073612AV
14
18033
AR053400CG
15
17853
ST158300AV
16
18038
ST116400AV
17
18043
AA021800AV
18
18048
ST073613AV
19
18053
WA005501AV
20
18058
CV006412AV
21
18063
ST128415AV
22
17773
GA016900AV
23
17873
HF203300AV
24
17793
WL024501AV
25
17878
GA016901AV
26
18068
VT470000KB
27
18073
ST186600AV
28
18078
PU015900AV
29
18083
PU015400AV
30
18088
KE000900AV
31
18093
ST012200AV
32
18098
BG208800AJ
33
18103
NG002502AV
34
18108
ST070625AV
35
18113
ST011200AV
36
18118
AL014000AV
37
18123
ST164100AV
Description
Montage du dispositif de protection de
la courroie
Vis de pression
Courroie (4L510)
Filtre équipé
Cartouche filtrante
Vis
Tube de nylon de 3/8 po
Raccord à coude
Soupape de sûreté ASME
Vis torx
Poignée de manche
Robinet de purge
Fiche
Réservoir d'air
Pied en caoutchouc
Vis
Tige d'arbre de roue
Bouchon
Roue pneumatique 10" (2,54 cm)
Commande d'obturateur
Déchargeur d'obturateur
Manomètre, gauche
Raccord
Ensemble rég. (inclut 22, 23 et 25)
Manomètre, droite
Pompe
Tuyau de décharge
Volant
Poulie
Clé 3⁄16 po
Vis de pression à tête carrée
Assemblage d'ancre
Moteur
Vis à tête hexagonale
Rondelle
Contre-écrou
Dispositif de retenue des fils
Fr21
Qté
1
1
1
1
1
4
1
2
1
4
2
2
2
1
4
4
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
4
8
4
1
Publicidad
Capítulos
