NightStick TWM-350 Manual De Instrucciones

Instruction Manual
TWM-350/850
Please read these instructions before using your Nightstick TWM-350/850. They
include important assembly and operating instructions.
PACKAGE CONTENTS
y 1 - Weapon Mounted Light
y 2 - CR-123 Lithium Batteries
y 2 - Cross Rail Inserts (1 pre-installed & 1 spare)
y 4 - Cross Rail Mounting Cap Head Screws (2 pre-installed & 2 spare)
y 1 - Allen Wrench
WEAPON SAFETY
PLEASE BE SURE TO READ, UNDERSTAND AND FOLLOW THESE SAFETY
AND OPERATING INSTRUCTIONS WHEN HANDLING A FIREARM OR THE
NIGHTSTICK TWM WHEN MOUNTED ON A FIREARM. FAILURE TO DO SO CAN
BE DANGEROUS AND COULD RESULT IN SERIOUS INJURY, DAMAGE TO
PROPERTY, OR DEATH.
Use of a fi rearm under any circumstance is inherently dangerous. SERIOUS
INJURY OR EVEN DEATH may result without proper training in the safe handling of
fi rearms. Proper training should be obtained from an accredited fi rearms safety program
conducted by a qualifi ed instructor.
Read, understand and follow all of the safety instructions that came with your fi rearm
before attaching your new TWM.
y Always assume every fi rearm is loaded and treat that fi rearm as such.
y Never point a fi rearm at anything that you are not willing to destroy.
y Never service your fi rearm or your TWM when mounted on a fi rearm without fi rst
activating the weapon's safety (if applicable), removing the magazine, opening the
action and physically and visually inspecting to make sure that no ammunition is
installed in the fi rearm.
WEAPON MOUNTED LIGHT SAFETY
y Nightstick recommends that the TWM should only be activated with the non-trigger
hand (support hand) while employing a two-hand grip on the fi rearm and with the
trigger fi nger fully outside the trigger guard when applicable.
WARNING: FAILURE TO DO SO COULD RESULT IN AN ACCIDENTAL DISCHARGE
AND SERIOUS INJURY, DAMAGE TO PROPERTY, OR DEATH.
y Thoroughly practice (employing safe training conditions) with the TWM and an
unloaded fi rearm before using the weapon.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
BEFORE ATTACHING, INSPECTING OR SERVICING THE TWM
y Engage the safety on the fi rearm (if applicable).
y Remove the magazine from the fi rearm (if applicable).
y Open the action and visually and physically inspect the chamber to be sure it is empty.
y Keep the barrel pointed in a safe direction at all times and never place your hand in
front of the muzzle.
WARNING: IT IS IMPERATIVE THAT SAFETY MEASURES BE EMPLOYED AT
ALL TIMES WHILE HANDLING A FIREARM.
GENERAL SAFETY WARNINGS
y NOT FOR USE ABOVE HAZARDOUS LOCATIONS
y DO NOT use in explosive atmospheres, near fl ammable liquids, or where explosion
proof lamps are required.
y DO NOT use in the proximity of vehicles or equipment when there is a risk of
fl ammable liquids coming into contact with the fl ashlight.
y DO NOT expose the batteries to water or salt water, or allow the batteries to get wet.
y DO NOT store the batteries with metallic objects that may cause a short circuit.
y Immediately discontinue use of the batteries if they emit an unusual smell, feel hot,
change color, change shape or appear abnormal in any way.
y Keep out of the reach of children.
STEP 1. INSTALL THE BATTERIES
Image 1
y To install the included CR-123 Lithium Batteries in the TWM, begin by unscrewing
the screw on the battery compartment door. (Image 1) This screw is designed to
remain in the battery compartment door once it has been unscrewed, do not attempt
to remove it.
y Insert both batteries into the battery compartment paying attention to the battery
orientation marking on the sides of the light near the battery compartment door. (Image 2)
y Re-install the battery compartment screw by pressing the door fully closed and then
tightening the screw until it is hand tight. Do not over tighten. (Image 3)
y Test the operation of the light (see OPERATION below).
STEP 2. INSTALL THE LIGHT ONTO YOUR FIREARM
The TWM is designed to be easily attached and detached from the fi rearm's tactical
rail. However, the fi rearm must have a tactical rail and it must have at least one cross rail
slot. The TWM is not designed to be used on a fi rearm that does not have a cross rail slot.
IMPORTANT: Your TWM comes with the Universal Insert pre-installed in the slot
location that will allow the light to fi t on approximately 70% of the handguns on the
market today. If the fi t is not correct for your specifi c handgun, use the included Allen
Wrench to relocate the Insert to the slot location that works best for your fi rearm.
Image 4
y Push inward on the head of the Rail Clamp Tension Thumbscrew to fully open the
Adjustable Portion of the Rail Clamp. (Image 4)
y While making sure that your fi rearm is in a safe condition and that the barrel is pointed
in a safe direction, place the fi xed portion of the Rail Clamp into the groove of the tactical
rail on your fi rearm and align the Cross Rail Insert with the slot on your fi rearm.
y Rotate the TWM onto the tactical rail (Image 5) and then release the pressure on the
Tension Thumbscrew making sure that the TWM is gripping both sides of the tactical
rail of your fi rearm and verify that the Cross Rail Insert is fully seated into the tactical
rail slot of your fi rearm. (Image 6)
INS-TWM-350/850-18b
Image 2 Image 3
Image 5 Image 6