Meccanica Fadini Elpro S20 Folleto De Instrucciones página 11

S20
GB
FUNCTIONS
Automatic / Semi-automatic:
Automatic cycle: after an opening pulse, the bollard goes down, it stops for dwell time pre-set in trimmer
T2, after the pre-set time it closes automatically
Semi-Automatic: after an opening pulse, the bollard goes down.
A closing pulse is needed to close.
Pedestrian Opening:
This command is separate from the standard
opening command. When all the posts are in up
position, on pulsing input P Dip-Switch 6= On,
and 3=On , post n1 (Motor M1) goes down for
pedestrian opening, for the time pre-set in
Trimmer T2, after this time it closes automatically.
The function "Pedestrian Opening" is not in service
during the first operation cycle, after a power failure.
Hold on switched (Deadman) control:
Open and Close operations are achieved "by holding a switch on"
(no relay self-holding is involved) therefore a physical attendance is
required to keep the post opening or closing until either the button
or key is released.
External Clock (Optional):
CLOCK: The electronic programmer Elpro S20 can be connected to a clock for the post opening and closing.
Connection: connect in parallel the NO clock contact to the 4 OPEN and 3 COMMON terminals, automatic closing is by
Dip-Switch n3=ON
How it works: Set the clock to the required time. On the pre-set time the post is automatically opened (the post goes
down) and held open (the flashing light goes off and the led flahes twice and dwells). Any further pulsing (even by remote
control) is not accepted by the system until the time pre-set by the clock has expired. On expiring and after the pre-set
dwell time the post rises automatically.
-
T2
from 1 to 180s
Plug-in traffic lights interface (Optional):
The interface power supply (230V 50Hz 100W output per lamp) is independent from the one of the programmer.
It can work also with the 2 lamps, Red and Green traffic lights (Dip Switch 8=OFF and 9=OFF)
Working logic:
- GREEN Light= Post in down position, OPEN passage
- RED Light= Moving post or in up position, CLOSED passage
- YELLOW Light= it lights before the switching from the Green light to the Red light
Note: During Pedestrian mode the traffic light is always RED.
DIP-SWITCHES 8 and 9
Dip-Switch 8=OFF and 9=OFF
The yellow light turns on for the time of 0s and after 0s the Red
OFF OFF
light turns on and the post starts rising immediately
8 9
Dip-Switch 8=ON and 9=OFF
ON
The yellow light turns on for the time of 2s then the Red light
OFF
turns on and after 2s the post starts rising
8 9
Dip-Switch 8=OFF and 9=ON
ON
OFF The yellow light turns on for the time of 6s then the Red light turns
8 9
on and after 5s the post starts rising
Dip-Switch 8=ON and 9=ON
ON ON
The yellow light turns on for the time of 10s then the Red
8 9 light turns on and after 7s the post starts rising
ELECTRONIC PROGRAMMER UP TO 2 BOLLARDSWITH OR WITHOUT LIMIT SWITCHES
57 58
+
Dwell time
DIP-SWITCH 3 - 6 both on ON
ON= Automatic closing
OFF= No automatic closing
3
semi-automatic closing
ON= Pedestrian opening Motor M1
OFF= Standard operation
6
DIP-SWITCH 7
ON= Deadman control
OFF= Standard operations
7
DIP-SWITCH N3=ON Automatic closing
ON= Automatic closing
OFF= No automatic closing.
3
Semi-automatic function
11
DIP-SWITCH 3
-
+
ON= Automatic closing
T2
Dwell time OFF= No automatic closing.
3
Semi-automatic function
from 1 to 180s
-
Dwell time
from 1 to 180s
3 4
Power supply
230V 50Hz
63 64 65 66 60 61
Fuse 1A
Red
Yellow
Green
(Optional: Plug-in PCB for
230V traffic lights)
code 7282L
meccanica
FADINI
+
T2
External clock
NO
RED
YELLOW
GREEN