Tabla de contenido
Publicidad
MAINTENANCE
5.
The sprayer needs very little maintenance, if you follow the steps mentioned in this manual its useful life will be very long.
Do not keep the sprayer with pressure after finishing your spraying job, release the pressure through the nozzle pressing the trigger, then take
the cap and strainer out and pour the remaining solution, dispose properly.
Now rinse the system with fresh water as follows:
Pour approximately 1/2 gallon of fresh water in the tank, pressurize and flush, the pumping system by pressing trigger at least 2 minutes, then
drain all remaining water.
Carrying straps are made of non-absorbent materials, nevertheless in case of solution spillage, wash them with fresh water to eliminate all risk
of skin irritation.
A unit that has been used with herbicides should never be used to spray insecticides, unless the sprayer has been properly cleaned and all
other chemicals neutralized. Failure to do this could cause you to kill plants that have been sprayed.
Always follow manufacturer's instructions of the chemicals in use to avoid accidents and take maximum advantage of the product.
Store your sprayer clean, empty and dry in a place protected from sunlight.
NOTE:
To keep your sprayer in good conditions of use it is necessary to maintain oiled the following parts
with grease:
The nozzle O-rings, gun o-rings, pistonsleeve, breather valve, cap gasket .
5.1 MAINTENANCE GUIDE
Instructions for maintaining your sprayer:
Rinse with clean water both externally and internally, to avoid risk of contamination.
To keep your sprayer in good condition it is recommended to change the following parts when servicing your sprayer No. 501-204 -C1:
- Checks and O-rings for the cylinder
- Piston sleeve
- Gun O-rings
- O-ring for pressure chamber
- O-rings for nozzle
- Breather valve
- Cap gasket
Disassembly instructions:
1. Remove the screw on the top of the lever.
2. Remove the screws of the rocker .
3. Pull the rocker out to remove the piston .
4. Unsbolt the cylinder (for this you need the key No. 219-003 ) .
5. Once the O-rings replaced and the ring reassembly the sprayer following steps on point 3.3.2..
NOTE:
To lubricate all pieces, use multipurpose grease.
5
3.2
DATOS TÉCNICOS
ESPECIFICACIONES
Modelo
Capacidad total del tanque
Boca de alimentación
Cintas
Sistema de bombeo
Anillo pistón
Manguera
Pistola
Tubo rociador
Boquilla
Descarga aprox a 3 bar/min
Presión de trabajo
Peso neto
Peso con caja
Dimensiones
ENSAMBLE
3.3
3.3.1
Partes que usted recibirá:
- 1 Pulverizador con manguera y pistola
- 1 Palanca de bombeo
- 1 Tubo rociador
- 1 Tapadera del tanque
- Folletería
- Dentro del tanque encontrará:
- 1 Coladera
En una bolsa de plástico encontrará:
- 1 Boquerel ajustable con tuerca
- 1 Tope plástico
- 1 Llave de 1/2"
- Tornillería completa
- 2 Rondanas seguro
427001
16.0 L / 4.2 US gal
14.0 cm
Poliester no absorbente de 38 mm de ancho con hombreras
Pistón con fuelle
Elastómero 45 mm
Vinilo con refuerzo de fibra 3/8" DI
Con filtro y palanca
Fibra de vidrio 52 cm - 20.5"
Ajustable de plástico
800 ml / 0.2 US gal
(2-4) bar - (29-58) psi
4.7 kg / 10.36 Lbs
5.2 kg / 11.46 Lbs
Alto 20 11/16 52.2 x largo 14 3/16 36 x ancho 8 1/4 21 cm
10
Publicidad
Tabla de contenido
