3M Speedglas H-701R Guia De Inicio Rapido

3
™
Speedglas
Welding Helmet
Welding Helmet 100 and Attachment for use with 3M
Hardhat H-701R, and Other Alternate Hardhat Confi gurations
** Refer to 3M™ Speedglas™ Welding Helmet 100, 3M™ Hardhat H-701R, or Listed Alternate Hardhat
Complete User Instructions for List of Product Warnings and Proper Use.
Ensemble masque pour soudeurs et adaptateur de casque
dur 100 Speedglas à utiliser avec le casque dur H-701R
™
3M et d'autres confi gurations de casque dur
™
** Consulter les directives d'utilisation complètes du masque pour soudeurs 100 Speedglas™ 3M™,
du casque dur H-701R 3M™ et des autres casques durs indiqués pour connaître les mises en garde et
les directives d'utilisation adéquates du produit.
Careta para soldadura 100 y Adaptador para uso con Casco
™
3M H-701R y otras confi guraciones alternativas de casco
** Remítase a las Instrucciones de la Careta para soldadura 3M™ Speedglas™ 100, del Casco 3M™
H-701R o del casco alternativo listado para consultar la lista de advertencias y uso adecuado del
producto.
3M Occupational Health and
Environmental Safety Division
3M Center, Building 0235-02-W-70
St. Paul, MN 55144-1000
© 3M 2012. All rights reserved.
V-Gard is a registered trademark of Mine Safety Appliances Co. – MSA.
3M and Speedglas are trademarks of 3M Company, used under license in Canada.
3M Occupational Health
and Environmental Safety Division
3M Canada Company
P.O. Box 5757 London, Ontario N6A 4T1
© 3M 2012. All rights reserved.
V-Gard is a registered trademark of Mine Safety Appliances Co. – MSA.
3M and Speedglas are trademarks of 3M Company, used under license in Canada.
Division des produits d'hygiène
industrielle et de sécurité
environnementale de 3M
Compagnie 3M Canada
C.P. 5757
London (Ontario) N6A 4T1
© 3M, 2012. Tous droits réservés.
V-Gard est une marque déposée de Mine Safety Appliances Co. – MSA.
3M et Speedglas sont des marques de commerce de 3M, utilisées sous licence au Canada.
3M México S.A. de C.V.
Av. Santa Fe No. 190
Col. Santa Fe, Del. Álvaro Obregón
México D.F. 01210
© 3M 2012. Todos los derechos reservados.
V-Gard es una marca registrada de Mine Safety Appliances Co. – MSA.
3M y Speedglas son marcas comerciales de 3M Company, usadas bajo licencia en Canadá.
• This product is designed to help protect the wearer's eyes and face from harmful radiation
including visible light, ultra-violet radiation (UV), infra-red radiation (IR), sparks and spatter
resulting from welding processes. These products must be used only by qualifi ed persons
who are properly trained in their use and maintenance. Misuse may result in permanent
eye injury and vision loss. Always wear ANSI Z87.1 compliant safety spectacles in addition
™
to any welding helmet. For proper use, see supervisor, or User Instructions or call 3M in
U.S.A. at 1-800-243-4630. In Canada, call Technical Service at 1-800-267-4414.
• This is an addendum to the User Instructions for the 3M™ Speedglas™ Auto-Darkening
Welding Helmets 100. Always read and follow the User Instructions provided with each
individual component of any welding helmet or hard hat assembly. User Instructions include
important warnings and use limitations. Failure to do so may result in sickness or death.
• Do not use any welding product without appropriate training. For proper use, see supervisor
or User Instructions or call 3M in U.S.A.1-800-243-4630. In Canada, call 1-800-267-4414.
Failure to do so may result in sickness or death.
• Always wear ANSI Z87.1-2003 compliant safety spectacles in addition to any welding
helmet. Failure to do so may result in permanent eye injury and vision loss. In Canada,
follow CSA Z94.3 and/or the requirements of the authority having jurisdiction in your region.
• Do not use with parts or accessories other than those described in these User Instructions.
Failure to do so may result in sickness or death.
• Make no modifi cations to the H-701R shell or suspension. Improper use may result in
serious injury or death. If the hard hat is subject to an impact, replace immediately.
• Do not use strong solvents such as aromatic hydrocarbons or ketones to clean the helmet
98-0060-0168-3/2
34-8709-9299-6
shell. These solvents can cause deterioration to the shell's ability to withstand impact and
penetration. Use of these solvents for cleaning may adversely affect product performance
and result in serious injury or death.
Introduction
Two ANSI standards cover performance requirements for welding helmets combined with hard
hats: Z87.1-2003 Eye and Face Protection Devices and Z89.1-2009 Industrial Head Protection.
Both standards require welding helmets and hard hats to be tested as a complete assembly, as
they would be worn by a welder. Assembling a welding hard hat using components from different
manufacturers or brands voids ANSI compliance unless tests verify that the assemblies remain
compliant with the ANSI requirements.
These User Instructions cover the 3M™ Speedglas™ Welding Helmet 100 models listed in Table 1,
mounted to certain hard hats that have been independently tested for compliance with the above
referenced ANSI standards. In all cases, the 3M™ Speedglas™ 100 Hardhat Adapter for Speedglas
100 helmets (part number 07-0014-00NR) was used as the mounting device.
IMPORTANT: To maintain ANSI compliance, use only the exact components listed in these User
Instructions.
Specifi cations
− Eye and Face Impact: ANSI Z87.1-2003 high impact protector (Z87+)
− Head Impact: ANSI Z89.1-2009, Type I (top impact). Refer to hard hat literature for electrical
rating.
Speedglas™ Helmet Model
07-0012-10BL
07-0012-11BL
07-0012-31BL
07-0012-31XX
Hard Hat Options
The confi gurations that were tested and passed the above referenced ANSI impact test
requirements are summarized in Table 2. Use with hardhats other than those listed in Table 2 have
not been tested as complete assemblies and would void compliance with the above referenced
ANSI standards. These User Instructions do not cover 3M™ Speedglas™ ProTop or other 3M™
Speedglas™ Systems sold complete with hard hats.
Manufacturer Hard Hat Model
3M 04-0023-02 (H-701R)
MSA V-Gard® w/Fas-trac Suspension
Assembly Instructions
1. Follow Figs. 1-4, to properly remove and replace the 3M™ Speedglas™ Headgear 100 with the
3M™ Speedglas™ Hardhat Adapter 100 (part number 07-0014-00NR) as shown in Figs. 1 and 2.
2. Assure to re-confi gure the head suspension in the hardhat to face the brim backwards as is
shown in Fig.3.
3. Attach the 3M™ Speedglas™ 100 assembly to the hardhat as shown in Fig. 4 and adjust the
hardhat
adapter "pin lock" for a tight fi t around the hardhat for a completed assembly.
FOR MORE INFORMATION
In United States, contact:
Website: www.3M.com/PPESafety
Technical Assistance: 1-800-243-4630
For other 3M products:
1-800-3M-HELPS or
1-651-737-6501
W
WARNING
Table 1. 3M™ Speedglas™ Welding Helmet Options
Description
100, ADF 100, Shade 10, Black
100, ADF 100, Shade 11, Black
100, ADF 100V, Shades 8-12, Black
100, ADF 100V, Shades 8-12 with Graphics
Table 2. Hard Hat Options
Hard Hat Part No.
70-0716-2145-5
475358 thru 475365 & 488146
Fig. 1
Fig. 2
Fig. 3
Fig. 4