EURO-PRO Shark SV746 Instrucciones Para El Uso Y Cuidado página 7

Modèle SV746
14,4 V CC
1. Coupelle à poussière
2. Bouton de relâche de la
coupelle à poussière
3. Commutateur marche/arrêt
4. Boîtier du séparateur
5. Filtre de la coupelle
6. Voyant de recharge
7. Appareil principal
8. Boyau de rallonge
Remarque: les piles de l'aspirateur sans cordon modèle SV746
ne sont pas chargées au moment de l'envoi. Ainsi, il est requis de
charger les piles pendant 16 à 20 heures avant l'usage initial.
9. Brosse transformable
10. Bec à raclette
11. Adaptateur de recharge
12. Suceur plat
13. Tube de rallonge avec joint de
scellement
13A. Tubes de rallonge (x2)
14. Brosse à planchers
15. Socle de recharge
16. Prise de recharge
16
OPERATING INSTRUCTIONS
Battery Pack Replacement
& Disposal
This vacuum cleaner contains a nickel-
cadmium (Ni-Cd) batteries. Batteries must be
recycled or disposed of properly. Call your
nearest recycling center for information on the
recycling and disposal of nickel-cadmium (Ni-
Cd) batteries.
If uncertain as to how to remove the battery
pack, we suggest you take your wet/dry hand
vacuum to a reputable small appliance service
technician to have this service preformed.
The battery pack of your SV746 is
replaceable, however care should be taken
when doing so. Follow these steps when
replacement is required:
1. Open the battery pack compartment
by removing the single Phillips head
screw located in the recess at the rear of
the unit. NEVER open the battery
compartment except to change the battery
pack when required.
2. Remove battery compartment cover.
Set aside battery compartment cover
with the screw.
3. Carefully detach the two (2) electrical
connectors from the battery pack by
pulling straight out from the battery pack.
4. Lift out the battery pack and set aside.
5. Insert the new battery pack and re-
connect the terminals by pushing lead
wires onto battery tabs.
6. Tuck the wiring inside the battery
compartment so that the wiring does
not interfere with the battery compartment
cover when it is replaced.
7. Re-install the battery compartment cover
by sliding it over the battery towards the
front of the unit, making sure that the front
snap engages the body of the unit.
8. Replace the battery compartment cover
screw.
WARNING
: NEVER use ordinary
batteries for replacement, as these may leak
and damage your vacuum cleaner. Use only
battery pack XBP746 provided by EURO-
PRO Operating LLC for replacement.
CAUTION
: NEVER use the unit without
the battery compartment cover in place.
NOTE
:
Any other servicing should be
performed by an authorized service
representative.
CAUTION
•
Use only with the battery pack supplied
with the unit.
• Do not attempt to remove the battery
pack from the unit to charge it.
• Never attempt to throw the battery pack or
unit into a fire or incinerate it.
• Do not attempt to remove or damage the
battery casing.
• Battery must be recycled or disposed of
properly at the end of it's service life.
Hints for Spot Cleaning Carpets
Note: Before spot cleaning your carpet, test for
color fastness. Dampen a white cloth with the
cleaning solution that you will be using and test
a small area in a closet or under a piece of
furniture. Gently rub the cloth over the area.
Check each color for bleeding. If the cloth
remains white, it should be safe to clean the
carpet or upholstery. When using commercial
pre-cleaners spot removers, follow
manufacturers instructions and follow this
procedure with our Wet/Dry Vac.
1. Apply the pre-cleaner spot remover to the
carpet as per manufacturers instructions.
2. Using the Wet/Dry vacuum, suck the pre-
cleaner spot remover liquid from the
carpet.
3. Spray the same area with water.
4. Vacuum again to remove the water.
5. Repeat steps 3 and 4 again if necessary.
6. Empty the dust cup.
7. If you still see that the pre-cleaner has
not been completely removed, repeat steps
3 and 4 again.
8. If the stain has not been removed, repeat
steps 1 to 6 again.
NOTE: Pre-cleaner spot removers sometimes
do not remove tough stains. Please use a
professional carpet cleaning service if such is
the case.
Wall Mounting Bracket
1. Make sure that the intended wall area
for the wall mounting bracket to be
drilled is free from any hidden
electrical wires, water pipes and gas
lines.
2. Select an appropriate place close to a
wall power outlet (120V., 60 Hz).
3. Do not mount near direct sunlight, near a
heat source or outdoors.
4. Select an appropriate drill type for the
material to be drilled.
5. Carefully measure and mark the location
of all bracket holes and then drill holes
and screw the wall mounting bracket onto
the wall.
5