2x Series Lightbar (with 3 or 4 Wires and Black Tops)
CLEANING & CARE OF YOUR LIGHTBAR:
Keeping the lenses clean and scratch free will optimize the performance of
the lightbar. The exterior of the lightbar including lenses should be cleaned
with mild soapy water and a soft cotton cloth to remove dirt, grime and
insects. Never use window cleaners or harsh chemicals on the lenses; this
may cause failure of the lenses or reduce clarity resulting in the reduction of
light output.
MOUNTING INTEGRITY:
A review of bolt/hardware/mounting bracket integrity should be performed
at the beginning and end of each shift.
WARNING MESSAGES - PLEASE READ:
WARNING - DRILLING ANY HOLES INTO THE LIGHTBAR IS NOT
RECOMMENDED! THE RISK OF DAMAGING INTERNAL COMPONENTS
AND THE RESULTING FAILURE OF THE LIGHTBAR WILL VOID ANY
WARRANTY OF THIS PRODUCT.
WARNING - CARE MUST BE TAKEN WHEN DRILLING THROUGH THE
ROOF OF THE VEHICLE NOT TO DRILL INTO ANY EXISTING WIRING
AND NOT TO DRILL THROUGH THE HEADLINER OR SUPPORT
MEMBERS OF THE VEHICLE. CHECK BOTH SIDES OF THE MOUNTING
SERVICE PRIOR TO DRILLING. DE-BURR ANY HOLES AND REMOVE
ANY METAL SHARDS OR REMNANTS. INSTALL GROMMETS INTO
ALL WIRE PASSAGE HOLES.
WARNING - ROUTE WIRES ONLY IN LOCATIONS THAT ARE NOT
SUBJECTED TO POTENTIAL WEAR. MAKE SURE TO AVOID ROUTING
WIRES IN THE DEPLOYMENT AREA OF YOUR AIR BAG. REFER TO
YOUR VEHICLE OWNER'S MANUAL FOR AIR BAG DEPLOYMENT
ZONES.
WARNING - ALL CUSTOMER SUPPLIED POWER WIRES CONNECTING
TO THE POSITIVE (+) OR NEGATIVE (-) BATTERY TERMINAL OR
LOCAL CHASSIS GROUND (-) MUST BE SIZED TO SUPPLY AT LEAST
125% OF THE MAXIMUM CURRENT AND PROPERLY FUSED AT THE
POWER SOURCE WITH APPROPRIATELY RATED FUSE.
IMPORTANT: When passing cables through fire wall or other sheet
metal, insert grommet to protect the cable!
6.
WARRANTY & RETURN GOODS PROCEDURE
WARRANTY RETURN PROCESS:
Please contact your SoundOff Commercial Vehicle Products (CVP) Sales
Representative or Customer Services staff (616.662.6199) for a RMA #,
Return Merchandise Authorization Number.
The following information is required for issuance of the RMA #:
• Reason for returning the product*
• Address where replacement product is to be shipped*
• Telephone number where you may be reached*
• CVP invoice number on which product was purchased**
• CVP part number and serial number**
• E-mail address where RMA # should be e-mailed**
• Fax number where RMA # should be faxed**
* RMA # will not be given without this information.
** If available, please provide this information.
CVP will NOT accept returns without an RMA #. Each RMA # is good for
only one (1) return and will expire (10) days after the date it was issued.
Products must be shipped back to CVP and the RMA # clearly marked on
the outside of the package near the shipping label. Please use the following
address on your shipping label:
SoundOff CVP
Attn: RMA Department
RMA # (type your number here)
3630 Highland Drive
Hudsonville, MI 49426
WARRANTY ExCLUSIONS:
Shipping & Handling, labor and service fees are non-refundable. CVP is not
liable for any damage due to installation or personal injury as a result of using
SoundOff Signal product.
WARRANTY FORFEITURE:
Warranty will not be granted if the Warranty Return Policy & Procedure rules
are not strictly followed. Physical damage resulting from customer abuse will
void warranty. Warranty will also be voided if any CVP and/or manufacturer
serial tags, product stickers, seals, or the like, are removed, altered or
tampered with. Returned product that is damaged by shipping via the RMA #
procedure is not the responsibility of CVP.
Document effective date on cover and below supersedes previously dated
policies and statements.
There are no other warranties, expressed or implied, including, but not limited
to, any implied merchantability or fitness for a particular use. CVP reserves the
right to modify this warranty statement at any time; or to discontinue, modify,
or upgrade any products of its manufacture with design improvements without
prior notice.
Series 2Xwith3or4WiresAndBlackTops 1017