Kimex 164-4920 Manual Del Usuario página 101

UART 1
Wifi & BT
(Optional)
Menu lock
Auto Source
Switch
Power Up Settings
Power Up Mode
Quick Standy
Power on Delay
Auto Launch
Boot Up Picture
Mode
HDMI1 Wake Up
HDMI2, HDMI3,
HDMI4 Wake Up
(optional)
Select ASCII/HEX protocol for UART 1. Default value is HEX. There is no need to
restart the Display after selection in order to work with the protocols correctly. If the
selection is changed, the latest selected protocol will be preserved and started when
the Display is booted up.
Note that ASCII/HEX selection is always working as expected. It does not matter if the
debug logs are enabled or not.
Also note that HEX protocol will work with the baud rate value 9600 for UART1
Sets the source option for these funtions. Auto, Display and Android options will be
available.
You can block the usage of the menu button on the remote by setting this item as All
menus. When you press the menu button, you will be asked to enter the PIN that
you have defined in the First Time Installation. Set as Off to disable this function.
If this option is enabled the Display will switch to the currently active HDMI source
automatically when a device is connected to the Display through the HDMI1 or
HDMI2 input socket. Set as Enabled to enable this feature.
When the HDMI source is removed the Display will switch to other active HDMI
source. If there isn't any other device connected to the Display and the HDMI Wake
UP option for the related HDMI source is enabled the Display will switch into the
standby mode.
There is also a 3-second restriction for the successive connected HDMI sources.
This means, second HDMI device must be plugged in 3 seconds after the first HDMI
device is plugged in.
Note: This feature applies for HDMI1 and HDMI2 input sockets only. Refer to the
General View section to see the HDMI inputs.
Configures the power up mode preference. Last State, Always On and Standby
options are available.
If this feature is enabled the Display can be turned on again with the RS232 and LAN
commands if it is turned off through it. Press Left or Right button to enable or disable
the feature.
Sets a delay value at power on. This value can be set from 0 to 2000 ms in steps of 100
ms. The Display will turn on after the set delay time is expired.
Configures the auto launch preference. CMS(Start url), Open Browser(Open Browser
initial page) and Disabled options are available.
Configures the picture mode preference at power on. If set as Off the last set picture
mode will be used at power on.
If this option is set as Enabled, the Display will turn on with the HDMI1 input source,
when it is switched on. This feature works based on HDMI 5V signal. When this signal
is active the Display wakes up and when the signal is inactive the Display shuts down.
You can disable this option by setting as Disabled.
conjunction with the Auto Source Switch feature it is recommended to enable the
Auto Source Switch option in the Signage>Controls menu.
If any Scheduler is set this option will be inactive and can not be set as Enabled.
Note: This feature may not be available depending on the model of your unit.
If this option is set as Enabled, the Display will turn on with the active input source
(HDMI2, HDM3 or HDMI4 depending on which input source is active), when it is switched
on. This feature works based on HDMI 5V signal. When this signal is active the Display
wakes up and when the signal is inactive the Display shuts down. You can disable this
option by setting as Disabled.
Auto Source Switch feature it is recommended to enable the Auto Source Switch
option in the Signage>Controls menu.
If any Scheduler is set this option will be inactive and can not be set as Enabled.
Note: This feature or HDMI3 and HDMI4 options may not be available depending on the model of your
unit. If multiple devices are connected to the Display through HDMI input sockets, this feature will not work.
English - 18 -
In order to use this feature in
In order to use this feature in conjunction with the