Tightness Inspection; Disposal - Nilfisk T22 Manual De Instrucciones

T22 - T40 - T40W
■ Fit the filter back in place, close the cover (2) and lock it by
means of the two the closing hooks (1).
Ti g h t n e s s i n s p e c t i o n
H o s e s c h e c k
Make sure that connecting hoses (1) are in a good condition
and correctly fixed.
If the hoses are damaged, broken or badly connected to the
unions, they must be replaced.
When sticky materials are treated, check for possible clogging
along the hose, in the inlet and on the baffle plate inside the
filtering chamber.
To clean, scrape the inlet (2) from the outside to remove
deposits.
Fi l t e r i n g c h a m b e r
e q u i p p e d w i t h d u s t c o n t a i n e r
If the gasket (1) between the container and the filtering chamber
(3) fails to guarantee tightness:
■ Loosen the four screws (2) that lock the filtering chamber
(3) against the machine structure.
■ Allow the filtering chamber (3) to lower down and tighten
the screws (2) once it has reached the tightness position.
If an optimal seal is not yet obtained or if there are tears, cracks,
etc., the gasket must be replaced.
Fi l t e r i n g c h a m b e r
e q u i p p e d w i t h L o n g o p a c
Ensure that the Longopac® bag is tight with the gasket (2).
Also check the seal of the gasket positioned on the discharge
clapet (1).
The gasket must be replaced if it is torn, cut, etc...
D i s p o s a l
GB
The crossed-out wheeled bin symbol on the equipment indicates
that used electrical and electronic equipment must be collected
and disposed of separately from household waste. The correct
disposal of the equipment will help prevent potential negative
consequences for the environment and human health.
Electrical and electronic household equipment must be
disposed of at the separate collection points in the residence
area. Please note that commercial electrical and electronic
equipment should be disposed of separately from the municipal
waste stream. We will be pleased to inform you about suitable
disposal options.
C 3 5 4
Fi g u r e 20
g a s k e t c h e c k f o r m a c h i n e s
Fi g u r e 21
g a s k e t c h e c k f o r m a c h i n e s
®
s y s t e m
Fi g u r e 22
Fi g u r e 23
Wi r i n g d i a g r a m s
Ba s i c m a c h i n e
C o d e
N a m e
T22 T40 / T40W
Z8 39915 Z8 39916
Q1
Z8 39932
M o d e l f o r v a c u u m i n g l i q u i d s
C o d e
N a m e
T22 T40 / T40W
Z8 39915 Z8 39916
Q1
Z8 39954
B1 Z8 391142
PR1 Z8 40841
F1.2 Z8 39244
TR1 Z8 391050
IC M o d e l
C o d e
N a m e
T40 / T40W
Q1 4089100301
A1 4083901505
1 6
Fi g u r e 24
D e s c r i p t i o n
Circuit breaker
Box for Q1
Fi g u r e 25
D e s c r i p t i o n
Circuit breaker
Handle for Q1
Auto release
Pressure switch
Fuse holder
Transformer
Fi g u r e 26
D e s c r i p t i o n
Circuit breaker
Cyclic timer
Q . t y
1
1
Q . t y
1
1
1
1
1
1
Q . t y
1
1