Assembly And Adjustments; Intended Use - DeWalt DWE1622 Manual De Instrucciones

Ocultar thumbs Ver también para DWE1622:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English

WARNING: Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face and body.

WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use. Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. D
if this tool does not operate, check power supply.

WARNING: This product is Class 1
Construction and must be connected to an
Earth connection.

WARNING: Do not operate this tool using D.C. power.
It may damage the tool electronics, which could
create an unsafe condition.
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

INTENDED USE

This heavy-duty drill press is designed for professional
drilling applications.
4
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n
........................ no load speed
o
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
WALT tools are factory tested;
e
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
This drill press is a professional power tool. DO nOT let
children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.
Installing the Machine (Fig. A, E)
1. Assemble the feed handle.
2. Fit the lubrication system as necessary.
3. Place the machine on a clean, level and solid
surface. Remove any particles that will obstruct full
contact between the magnetic base
mounting surface.
4. Fit and tighten the safety chain
Assembling the Feed Handle (Fig. A, B)
The quick-release feed handle
one simple operation both to the left and the right of
the machine.
1. Screw the handles
into the hub
 6 
are secure.
2. Keep the button
 17 
depressed while inserting the hub
shaft into the hole
 18 
.
3. Release the button.
Fig. B
2
1
6
Assemble the Drill Guard (Fig. C)
1. Hold the guard
 16 
in front of the tool holder, aligning
the slots in the guard with the holes
2. Fit the screws
  into the holes
 19 
of the frame.

WARNING: Always use the drill guard.
 15 
and the
.
 9 
 6 
can be mounted in
. Ensure handles
 7 
18
6
7
17
in the machine.
 20 
located in the front
 20 

Publicidad

Tabla de contenido
loading

Tabla de contenido