Safety Notes - ELCART 09/08535-00 Manual De Instrucciones

ART. 09/08535-00
1000A DC/AC CLAMP METER ART. 09/08535-00 NI 6010
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal,
indicates the user must refer to the manual for further
information.
This symbol, adjacent to a terminal, indicates that, under
normal use, hazardous voltages may be present
Double insulation

SAFETY NOTES

• Do not exceed the maximum allowable input range of any function
• Do not apply voltage to meter when resistance function is selected.
• Set the function switch OFF when the meter is not in use.
WARNINGS
• Set function switch to the appropriate position before measuring.
• When measuring volts do not switch to current/resistance modes.
• Do not measure current on a circuit whose voltage exceeds 240V.
• When changing ranges using the selector switch always
disconnect the test leads from the circuit under test.
• Do not exceed the maximum rated input limits.
CAUTIONS
Improper use of this meter can cause damage, shock, injury or
death. Read and understand this user manual before operating the
meter.
Always remove the test leads before replacing the battery.
Inspect the condition of the test leads and the meter itself for any
damage before operating the meter. Repair or replace any damage
before use.
Use great care when making measurements if the voltages are
greater than 25VAC rms or 35VDC. These voltages are considered
a shock hazard.
Remove the battery if the meter is to be stored for long periods.
Always discharge capacitors and remove power from the device
under test before performing Diode, Resistance or Continuity tests.
• Voltage checks on electrical outlets can be difficult and misleading
because of the uncertainty of connection to the recessed
electrical contacts. Other means should be used to ensure that
the terminals are not "live".
• If the equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment may be
impaired.
ELCART DISTRIBUTION SPA via Michelangelo Buonarroti, 46 - 20093 Cologno Monzese (Milano) ITALY
Tel. ++39 02.25117310 Fax ++39 02.25117610 sito internet: www.elcart.com
La divulgazione dei dati contenuti in questa scheda è da ritenersi un servizio puramente informativo e non costituisce alcun vincolo da parte della Elcart in merito a prestazioni ed utilizzo del prodotto.
The divulgation of data contained on this technical sheet are exclusively for informational reasons and establish no link on behalf of Elcart regard to thr performances and the usa of the product.
La divulgacion de los datos contenidos en esta ficha son un servicio unicamente informativo y no constituyen ningun vinculo de parte de Elcart respecto a las prestaciones y uso del producto.
ELCART
servizio automatico documentazione tecnica
OPERATING INSTRUCTION MANUAL
Input Limits
Function
A AC
V DC, V AC
Resistance, Diode, Continuity,
Capacitance, Frequency, Duty
Cycle, Test
Temperature (°C/°F)
Meter Description
1. Current clamp
2. Clamp trigger
3. Data Hold and Backlight button
4. Mode select button
5. Hz/% button
6. LCD display
7. COM input jack
8. Rotary Function swith
9. ZERO button
10. Range select button
11. V Ω°C/°F jack
12. Battery compartment on rear
1. AC DC
AC (alternating current) and DC (direct currrent)
2. Minus sign
3. 8.8.8.8
4000 count (0 to 3999) measurement reading
4. AUTO
AutoRange mode
5. Diode test mode
6. •))) Audible Continuity
7. HOLD Data Hold mode
9.°C/°F, µ,m,V,A,K,M,Ω, Units of measure list
PAGINA 4 DI 9
Maximum Input
1000A
600V DC/AC
250V DC/AC
60V DC/24V AC
1
A
4 0 0 A
4 0 A
2
3
4
H z %
5
6
¡ ã C
D C ¡ ã F
A
m V
A C
k M
7
n
u
e-mail: info@elcart.it
8
9