Cautions On Handling Discs; Connections - Denon DHT-500SD Instrucciones De Operación

ENGLISH
6

CAUTIONS ON HANDLING DISCS

Discs
Only the discs including the marks shown on page 5
can be played on the ADV-500SD.
Note, however, that discs with special shapes (heart-
shaped discs, hexagonal discs, etc.) cannot be played
on the ADV-500SD. Do not attempt to play such discs,
as they may damage the player.
Holding Discs
Avoid touching the surface of discs when loading and
unloading them.
Be careful not to get
fingerprints on the signal
surface (the side which
shines in rainbow colors).
Cleaning Discs
2 Fingerprints or dirt on the disc may lower sound and
picture quality or cause breaks in playback. Wipe off
fingerprints or dirt.
2 Use a commercially available disc cleaning set or a
soft cloth to wipe off fingerprints or dirt.
Wipe gently from the Do not wipe with a
middle outwards. circular motion.
NOTE:
• Do not use record spray or antistatic. Also do not
use volatile chemicals such as benzene or
thinner.
Record Thinner Benzene
spray
6
Cautions on Handling Discs
Do not get fingerprints, grease or dirt on discs.
•
• Be especially careful not to scratch discs when
removing them from their cases.
• Do not bend discs.
• Do not heat discs.
• Do not enlarge the center hole.
• Do not write on the labeled (printed) side with a ball-
point pen or a pencil.
• Water droplets may form on the surface if the disc
is moved suddenly from a cold place to a warm one.
Do not use a hairdryer, etc., to dry the disc.
Cautions on Storing Discs
• Always eject discs after playing them.
• Keep discs in their cases to protect them from dust,
scratches and warping.
• Do not put discs in the following places:
1. Places exposed to direct sunlight for long periods
of time
2. Humid or dusty places
3. Places exposed to heat from heaters, etc.
Cautions on Loading Discs
• Only load one disc at a time. Loading one disc on
top of another may result in damage or scratch the
discs.
• Load 8 cm discs securely in the disc guide, without
using an adapter. If the disc is not properly loaded,
it may slip out of the guide and block the disc tray.
• Be careful not to let your fingers get caught when
the disc tray is closing.
• Do not place anything but discs in the disc tray.
• Do not load cracked or warped discs or discs that
have been fixed with adhesive, etc.
• Do not use discs on which the adhesive part of
cellophane tape or glue used to attach the label is
exposed, or discs with traces of tape or labels that
have been peeled off. Such discs may get stuck
inside the player, resulting in damage.
7

CONNECTIONS

CAUTION:
• Switch off the power to all equipment before making connections.
• Read the instructions of each component you intend to use with this unit.
• Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the signal interconnection
cables together with the AC power cord or speaker cables
(1) Connection to a TV and other equipment
Connect the unit using one of the following terminations to your TV or monitor. The connections are listed in
order of quality of picture from the best possible first. Additional information on each connection type is
provided below:
If your TV or monitor is compatible with progressive scan, connect the TV via the COMPONENT VIDEO jacks
using a component video cable, and press the "PROGRESSIVE SCAN" button on the front panel so that
"P.SCAN" lights on the display. This results in a high quality picture with little flickering.
Progressive video signals are output from only component terminals.
Connecting the RGB SCART output(AV CONNECTOR) using an RGB-ready SCART cable, or connecting the
COMPONENT VIDEO using a component video cable is next to it.
S-VIDEO is your third choice.
Composite video output (SCART-COMPOSITE or VIDEO OUT) would be your last choice.
• For better picture quality, do not connect more than one video cable.
• Please connect this unit to a TV directly. If the TV is connected through a video cassette recorder, playback
of a copy protected DVD disc could result in distorted picture quality.
A COMPONENT VIDEO jack
If your TV or monitor has COMPONENT VIDEO IN jacks, connect them with a quality component video cable.
In the default setting, COMPONENT VIDEO OUT jack is not active. If you want to use COMPONENT VIDEO
OUT, follow the following steps.
1. Connect the VIDEO jacks with a RCA video cable.
You can use the provided cable.
2. Connect the COMPONENT VIDEO jacks with a component video cable.
3. Turn the unit and TV on, and select "COMPONENT" in the DVD SETUP menu.
4. Turn the unit off and disconnect the RCA video cable from the VIDEO jacks.
ADV-500SD
A
TV
P /C P /C Y
R R B B
COMPONENT VIDEO IN